ADB1100AWB1 Amana Dishwasher - Instructions

Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher

Replacement parts from factory installed using u tube support video


Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it click when you twist the new one on so you know the clip has engaged. Super easy.

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.

Only one friction sleeve was broken. So I pulled out the dishwasher to see how the one on the other side went on. It was very easy to replace and I replaced both. Unit works fine now.

As washer had been in place for several years, decided to go for new arms rather than clean the originals. Simple twist of the wrist to remove and another twist to install each new one. Slick as a whistle. Seem to work just fine.
Thank you,
EG

I removed the front of the dishwasher. Then removed the old dispenser assembly, and installed the new one. I don't have as many tools as I need here in our winter residence, so the job took a few more minutes than it would if I'd have had the correct tools.

Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!

The repair went okay. The problem was that the dishwasher would not run after the installation of the dispenser. The door was taken apart 2-3 times. I told my husband (the repair man) that we should pull out the dishwasher so I could clean behind it. I asked him 4 or 5 times to pull out the dishwasrer. Never an answer. Mind you he is an electrician by trade now retired. For some reason while I was not looking he did pull the unit out after 2 hours of fussing with this electrical problem. Remember he is an electrican by trade. When he pulled the unit out "THE PLUG WAS OUT OF THE SOCKET". How funny!!!!!!!!!!!!!!!!!!!!!!!!!!
I could not stop laughing. I had to answer the phone at that time and my friend thought I was out of breath from running for the phone. I told her later it was from the PLUG OUT OF SOCKET TRICK. I still am laughing. The first thing an repair mann will ask you is if the unit is pluged in. I have two sons and one son-in-law that are electricans and will have many years of fun telling this story. It is good to laugh. I will be laughing for a long time.

simply line up the new pin with the rectangular slot in the kick panel and metal panel behind, slide the pin in and turn it with a flat blade screw driver.
NOTE: the original pin was black. A black replacement part cost $29 plus shipping! A knock-off pin was only $6 plus shipping. I got the cheap one and colored it with a black Sharpee marker before installation.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

Followed directions from YouTube video.