AGR5715QDB Amana Range - Instructions

Simple... unscrew the 2 screws and unplug the electrical connection to uninstall and just the opposite to install.

I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".

I expected to see a thermocouple and a heating element next to the gas valve but after reviewing other PartSelect stories from people with a similar problem I realized that the heating element also serves as the switch. Apparently as the heating element is energized by the oven control it draws more amps. The gas valve is allowed to open at a specific level corresponding to a sufficiently glowing heating element. I ordered a new heating element. The part received was made up of two pieces. The heating element and the metal mounting bracket. The element was identical but assumingly due to the age of my stove the bracket was slightly different. Fortunatly I was able to slide the new element into the old bracket. The only other obsticle was that the new element came with a two conductor connector and the old was installed with ceramic wire nuts. The connector was cut off and the ceramic wire nuts were reused. Its working fine.

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

Husband did repair. He removed the
the ignitor. Was a little difficult to remove. I couldn't tell you what he did and in what order.

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.

Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.

It's happened before and the igniter has always been the problem. This time, however, the mounting holes were slightly off and had to be drilled out. The connector didn't mate up and so both had to be cut off, the wire stripped back and wire nuts used to make the connection. In the end, it all worked out. I guess since its kind of old, you can't stock every component for every oven. Oven works perfectly now.

Unplugged the Rang. Removed the oven door. Removed the lower cover for the Bottom heater. Removed the two screws that held the igniter to the burner. Went to back of oven to disconnect the igniter. removed the old igniter. Installed the new Igniter in the reverse order.

Removed the lower base pan of the oven by unscrewing two phillips head screws. I then had access to the old igniter and removed that by removing the mounting screws (2 Phillips head screws). Continuity test revealed an open circuit. I simply replaced the old part with the new part, reversed the process and the oven was ready for use in less than 10 minutes.

Diagnosed the issue by removing the bottom panel of the oven. (two little screws) Once the panel was out I turned the oven on with the door open to see what was happening.

Noticed that the heating element wasn't lighting up in order for the gas to ignite. Unplugged the oven and removed the heating element. Two screws hold the heating element in place. Removed those. Then, there is a panel on the back of the oven with one screw to remove. Once panel is removed you have easy access to the heating element connecting electric plug. Disconnect this plug by simply pulling apart.

Then, I was able to go back to the inside of the oven and slowly pull the heating element with plug out. The heating element had the part number on it. My oven is a Maytag which, is made by Whirlpool.

Went online to Whirlpool PartSelect and ordered my part. The part came in two days. Installed my new part and plugged in my oven to test the part. Part worked perfectly. Unplugged the oven and finished the installation process.

There are two elements to look at, one on top (broil) and one on the bottom (bake). Same element but may have different connectors. Double check before ordering.

same as taking out old part and i misdiagnosed the problem ordered wrong part first and parts select steered me ito the correct part thank you

Installing new igniter was very easy. The problem I had was removing the screws. The range is 18 yrs old. The screws were stuck from yrs of use. Especially in the oven cover plate. I used w- d 40 it didn't work. I decided to take a 2" putty knife and push it under the screw head to release it and it worked. They came right out. The igniter screws were also difficult to get out. Once those were removed, I pulled the stove out, turned off the gas and the electrical plug, removed back plate unplugged the old igniter and connected the new one. Easy, peasy. Turned gas on etc. Tested the oven to be sure it worked. Turned oven off.Then put it all back the way it was. Done! The igniter install was simple and qiuck. The time problem was the screws.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.