AGR5725RDB13 Amana Range - Instructions

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

Very easy install. Works great.

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

I took the door off, then took the bottom out removed two screws, unplugged the old igniter and installed the new one. I turned on the oven and tested the new igniter and then replaced the bottom and oven door.

Watch the video. Spot on instructions. Easy peasy.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

I ordered a new igniter and when it arrived, i removed the door from the oven. It just lift's off. I had to removed two screws from the bottom plate to gain access to the igniter. Remove the two screws from the igniter and unplug it from the back of the lower back of the stove. Place the new igniter where the old one was and plug it in. Put new screws in and tighten them down. Put the bottom plate back in its place with screws tightened. Put oven door back on and turn on the oven. That's all there is to it. Your done.

1. Remove the oven door by opening a few inches and lifting straight up. Remove racks to access it. 2. The old igniter is just held in by two nuts that have a screw head in the middle of them so they could be removed by a nut driver or by a screwdriver. Unfortunately, both of our screws threads were terribly stripped and after first trying to use pliers to help remove them, we ended up using a dremel tool to cut them off. 3. unplug the old igniter and take it out. 4. Plug in the new igniter. 5. attach the two screws. (our time on the repair was mostly spent trying to find two screws around our house that would replace the two that were stripped--otherwise this would have been 15 minutes). 6. return the door and racks by the sliding the door downwards onto the hinges

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

Removed door and bottom oven pan to expose igniter. It was held in place by two sheet metal screws. Tried to back them out but due to heat damage , they stripped. I used my versa tool with a metal blade to cut the screws. I removed the old igniter and disconnected the plug, after I guided it out from the insulation. I installed the new igniter with two new self tapping screws after I connected the plug and guided it back through the insulation. Reinstalled the oven pan and door. I set the oven to 350° and the new igniter worked. Wife is happy and I saved the repairman fees.