CE38600AAQ Crosley Range - Instructions

the hardest part of this repair was the wait for the element to arrive in the mail - which was in 4 business days - then took 5 to 10 minutes to get to circuit breaker box in garage. That was the longest part of the repair. My husband took the door off the oven after turning the circuit off in the garage. Followed directions from others who made the same repair and it was done in 2 minutes! Super easy - thanks for saving us money during this time of tight budgeting around the holidays! You're a lifesaver!

-Disconnected power from oven at the circuit breaker.
-Removed oven door and racks.
-Removed two screws holding element to the rear wall.
-Carefully pulled element away from rear wall, exposing wire leads.
-Carefully detached wire leads with male Sta-Kon connectors from element ends. (Taking care not to break or weaken the wires at the connector.)
-Disposed of old element and placed new element in same position.
-Re-attached leads by very carefully sliding male Sta-Kon connectors into the new element connectors, taking care not to push too hard and bend element wire.
-Gently re-inserted element ends into wall and re-attached element to wall with original screws.
-Reconnected power and tested new element. Element did not heat.
-Disconnected power and looked for collateral damage from original element failure.
-Removed oven from wall, removed rear panel and identified the high-temperature limit switch.
-Removed Sta-Kon leads and checked switch for electrical continuity. It had none, apparently the result of the high current from original element short.
-Obtained new hi-limit switch from Part Select
-Removed and replaced hi-limit switch, re-attached leads.
-Replaced rear panel and reinserted oven in wall.
-Reconnected power and tested new element. Element heated normally.
-Returned racks to oven, re-attached door and done.

Very easy to install with the advanced instructions you provided.

First, turn off the breaker to the range. Then just remove the 2 screws that hold the element at the back of the oven. Pull the wire connectors apart or push them off with a regular screwdriver. Instructions that I read said to make sure the wires don't fall back through the holes, but in our case the insulation held them in place. Reconnect the wire connectors to the new element and reattach with the screws. Easy!

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

Wonderful. Thanks

It was easy finding the part on line and the part was delivered within three days. It only took about 10 minutes to change element. I was so pleased with the product, that I just changed a thermostat on my parents stove which was purchased through parts select and that was very easy to change also.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Video showed element being unplugged from inside oven. My oven wires did not extend into oven cavity and they fell behind the back oven wall when I unplugged them. After trying to catch the two wires using needle nose pliers through 3/4" holes several times, I finally decided to take the complete back off the range. When I did this, I was able to see the wires with the female couplings. I then had my wife firmly hold the new element against the back of the oven from inside letting me connect the wires to the new element and replace the oven back. THIS WOULD HAVE QUALIFIED AS "EASY" AND A 15 TO 30 MINUTE JOB if this technique had been known from the outset.

Take out 2 screws. Unplug the old element, plug in the new one and put the screws back in.