All Installation Instructions for Gibson Range CEB3M2WSTB

Baker Element burned out

Really easy process. First I unplugged the oven for safety then I proceeded to remove the 2 screws that were holding the old element in place. Next I removed the old element then installed the new one. After installing the two screws I connect the oven back to its power source and BANG!............. It works like a charm

I give it a A+ installation

Parts Used:

Bake Element (240v)

James from Navarre, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The bake element burned out

I turned off the circuit breaker to the range. Next I removed the two screws that fastened the element to the rear of the oven. Then I pulled the element out far enough to be able to reach the spade clips and disconnected the element. I connected the replacement element to the clips and fastened it to the rear of the oven with the two screws. I turned the circuit braker on and the element functioned properly.

Parts Used:

Bake Element (240v)

Kenneth from Lake Luzerne, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bake element not working

Removed the old element by sliding the wires
attached to it. Unscrew 2 screws, slide the
new one to the wirings and put the 2 screws back.
It works. Praise the Lord.

Parts Used:

Bake Element (240v)

ROMEO from HANOVER PARK, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Baking element went out

Removed back cover, unhooked wires, unscrewed and removed bad baking element. Reverse order to install. Less than 15 min. repair job.

Parts Used:

Bake Element (240v)

Brandon from Lexington, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Heating element cracked.

First unplugged the stove, then removed the screws holding the element in place. Next I pulled the element out until the wires were visible and unplugged them. After removing the old element, I plugged the new one in and positioned it with the screws. Plug the stove back in and done.

Parts Used:

Bake Element (240v)

Scott from Great Falls, MT
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original terminal degraded and faulty

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Parts Used:

Terminal Block Kit

Robert from PRAIRIEVILLE, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old drip pans had turned to rusty lace.

Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.

Parts Used:

6-Inch Chrome Drip Bowl

8-Inch Drop Bowl

Helen from PAWLEYS ISL, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wrong part

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Parts Used:

Main Terminal Block Kit

Barbara from WICKENBURG, AZ
Difficulty Level:
Very Difficult
Total Repair Time:
30 - 60 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

uneven heating

Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.

Parts Used:

8-Inch Surface Element

Dan from CHEWELAH, WA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

needed new drip bowls and 2 new elements

pulled them out and replaced them

Parts Used:

8-Inch Surface Element

6-Inch Chrome Drip Bowl

8-Inch Drop Bowl

kathy from DAVIS, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Left an appliance on surface element and melted paint onto the element

Plug the new element into the space on stove

Parts Used:

6-Inch Surface Element

Kenneth from LANOKA HARBOR, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner would cutoff intermittently

Pulled out old burner/inserted new

Parts Used:

8-Inch Surface Element

Joseph from FREDERICKSBRG, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip bowls needed replacing

Removed the old ones and inserted the new ones.

Parts Used:

6-Inch Chrome Drip Bowl

8-Inch Drop Bowl

Doris from SUN CITY, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

right hinge on oven door broke. door would no longer shut, losing much heat.

Remove drawer, remove oven door, remove hinge and pieces. Get the spring loose. Attache new hinge to frame, reconnect spring. Slide door back on hinges.

Parts Used: