CRSH232PB3 Crosley Refrigerator - Instructions

It was very simple-it is just an insert glass shelf above the vegetable drawers. But, it was fairly easy to identify on your website and delivered in about two days.

I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

New valve is push fittings while old valve is threaded directions don't tell you but cut the tubing and it will match up correctly

removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

I unplugged the fridge and removed the dispenser's drip plate. There are 3 screws holding the front fascia. I carefully slid the fascia up to removed it. I unplugged it from what looks like a circuit board from the dispenser. Remove 3 more screws that held the board exposing the ice dispenser's hole and the water actuator. To give myself a little more room to work, I disconnected the board from the fridge. Attempted to removed the water hose but i couldn't, but found out didn't need to. I used a longer philip's screwdriver to unscrew two very small plates that were holding the actuator in place. Need a magnitized screwdriver for this, my hands are too big to reach in there. It took about 15 minutes. NO extra parts or additional parts to order.

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.

Replaced the Triple Water Valve

Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

No previous experience with this appliance, a 36 inch side by side unit. Had to determine how to access the area to replace the part. This is done from the front with the door closed. The bottom shelf in the dispenser area elevates and slips out. Retainer screws are then evident. Remove screws that hold trim and then unplug the electric attachment for the switches from the trim which contains the light and selection controls. Next remove the screws placed around the circuit board holder. This then allows the section attaching the ice dispenser and water dispenser to be pulled forward. Do not disconnect the water tube. Two small metal retainers for the water dispenser can then be removed (three small screws) carefully. Remove the broken part of the old actuator and place the new one in the slots. Replace the retainers (start the retainer screws by hand unless you have a magnetic screwdriver). Replace the section holding the circuit board; then the trim and the bottom shelf. Easier than anticipated.