CTE18EPERAD Hotpoint Refrigerator - Instructions

disconnect the power to the unit. remove the retainer sctrews on the mounting bracket. remove fan motor from unit. using the rerquired tools remove the fan from the old motor and install on the new one. torque the nut until all slack is out then 1/4 turn. reinstall motor assy. and reconnect power. test the system .

Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer
Certainly not PartSelect's fault. They have great service.

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove from hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.

Just removed the old gasket at one corner with screwdriver and pulled the rest off. Matched the gasket with the strip on the frig. and pushed it in all around. Works good.

From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.

the new gasket did not appear to exactly match the old one but it did seem like to correct size, and that it should work. I removed the old and worked the new one into the receiver bar with some good old thumb pressure. the door does not 'suck' closed but it seems to be forming around the frame and I do not feel any loss of cold air. All in all a simple process from picking up the phone to completion.....hopefully saved me the cost of a new fridge for a few more years?????

I placed the new part on the end of the freezer door guard and firmly pushed it in until it 'clicked'. Easy as pie! The more difficult part was to remove the broken off part inside the opening of the freezer door hwere the new bar end was to be inserted. I finally used thin nose pliers to reach in and grab the broken off part.

Start at the inside top corner and slowly work across the top, pushing with thumbs so that you feel it fitting into the groove. Go inch by inch. No speeding on this one. The gasket was so well packed that there were no folds or kinks, so no heating was necessary.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge

I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find someone as easy to follow for future videos. The videos are priceless for the repairs.

Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...

I just let the gasket sit on a flat surface for a couple of days. I didn't immerse it in hot water as the directions stated. It went on fairly easy. Just took a bit of patience. The fact that it was packaged nicely without it being jammed into a tight bundle probably was a big factor in the ease of installation.

Installed the new timer.