DBLR333GG1CC General Electric Dryer - Instructions

I followed the directions that were listed on this site by other Do It Yourself individuals...by the way I'm a lady and more mechanically inclined than my husband, but he was a great help in lifting the drum up and out. (I unplugged the dryer before starting repairs)
1. I removed the two screws located at the top of the dryer inside the door.
2. Top of dryer cabinet lifted up after screws were removed.
3. Located and removed front panel retension screws and removed front panel and set aside
4. slipped belt off motor by reducing tension on idler pully
5. Removed screws inside drum that secured drum to bearing assembly
6. Husband and I lifted drum up and out of cabinet (this went very smoothly and took less than 15 minutes time.
7. Followed supplied bearing drum instructions and removed old bearing and installed new assembly.
8. Thoroughly cleaned out internal cabinet, blower, and motor areas
9. Reset the idler pully into proper position.
10. Tipped dryer on 'back' to reseat the drum With A NEW DRYER BELT (taped temporarily around the drum) into the bearing shaft (I may not be using the proper terms)
11. tipped dryer upright and while Hubby balanced the drum, the front panel was resecured to the rest of the cabinet.
12. Removed temporarily applied tape that held the drum belt in the general position, then using the rear access panel, I slipped the belt over the motor into the proper posisiton.
13. Top cabinet was reapplied and screwed into
place.
14 Plugged in and tested the dryer...NO SQUEAKS and it works beautifully and quietly!!

The job is not terribly difficult, but I am only 5 feet tall and the drum is bulky to work with and balance. Reaching into the cabinet to slip the belt onto the motor stretched my arm to the limit.
I found the cabinet reassembly and realignment of the screw holes quite annoying. But the total job proved satisfying upon completion.

Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !

Disconnect Power from the Dryer
Remove 2 screws that held the top on the dryer.
Removed the 2 screw that held the front on the dryer.
Unhooked the belt from the tensioner and motor pulley.
Pulled the drum out. Removed the belt.
Removed the three screws that held the bearing assembly
on the back of the drum.
Removed the keeper o-ring slide the bad bearing off of shaft. Slide the new bearing on the shaft put the new o-ring on the shaft. Reassembled the bearing on back of the drum. Put belt back around the drum and put drum back in place. Put The belt around the motor pulley and tensioner
(this is probably the hardest part).
Put the front and top back together.
Turned the power back on. Job done

Replaced cycle thermostat.

my problem was easy, i orderd a new lint filter, for a
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......

disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working

I reviewed the video instructions on the website; these were invaluable to understand the task. Since the dryer drum had to be removed to replace the thermostat, it was prudent to replace the drive belt at disassembly. Great job on the videos to see the extra effort required to install the new belt around the tensioner pulley while supporting the drum. I will use this site again when a need arises, because they are quick to ship the ordered part(s) and help the DIY handyman make repairs via the videos.

When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!

1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.

Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!

Read the other posts - they are very good. On my particular dryer it took two Slide WH and two Slide Dryer Drum Side PS266785.

Most time spent was vaccuming out and removing a softball size ball of lint clogging the dryer - now it will actually dry clothes!

Part select delivery is really fantastic (even though it took me three orders to get it right!).

Took the few screws out replaced the part then put it back together.

I followed the instruction of the first posting for this category and it worked perfectly...thanks for the nice detail...

- Upon receipt from PartSelect, placed new slides in Drum Bearing (this does not come together or as a kit - must order 4 slides AND Bearing separately for this dryer model)
- Loosened Top panel screws (2) from inside door area
- Slid top of dryer off - PAY attention to HOW the top comes out (tabs at the back and slots on the sides) or replacing the top could prove frustrating)
- Loosened Front panel screws (2) and GENTLY leaned the panel forward to access Drum Bearing - no need to REMOVE the front panel but be aware of the switch wires when leaning and the weight of the door if you did not remove that
- Removed old Drum Bearing
- Vacuumend interior of dryer cabinet (especially area leading down to vent)
- Snapped new Drum Bearing into place
- Re-secured Front panel paying attention to drum position to make sure everything still rotated properly and freely
- Reset Top panel - align back tabs first, gently pull forward just a bit until Top slips down over side tabs, then slide back into place and re-secure

Worked like a charm - took about 20 minutes...

took out broken filter and replaced with new lint
filter.

Unplugged dry cord . Removed top and front cover. Removed drum to replace rear Bearing. Reinstalled drum replaced front bearings and sleeve. Reinstalled both covers and plugged in.