DCVH515GF3WW General Electric Dryer - Instructions

Top Bearing Felt

Top Bearing

michael from WELLINGTON, FL
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

belt broke on dryer

good replacement procedure on you tube.

Parts Used:

rodney from VANCEBORO, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

evidently the pulley spring on video was very very very weak

the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.

Parts Used:

tim from NEW PRT RCHY, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rubbing noise while dryer was running

Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!

Parts Used:

Carol from Simpsonville, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drum was squeaking and making a lot of noise!

Took apart the dryer housing fairly quickly, pulled out the drum, and installed the kit. Was fairly simple. Then reassembled. The hardest part was trying to get the belt on properly and reconnect to the motor. Believe it or not, I wasted most of my time on the belt. Should've watched the video better and listened to my wife and her suggestions.

Parts Used:

Dryer Rear Drum Bearing Kit

Timothy from Rochester, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

clothes being eaten first then the loud noise

I replaced front and rear bearing.The rear I replaced because of cause and effect.There was some play so I am glad I replaced the rear too. Make sure you order drum slides. Ken

Parts Used:

Dryer Rear Drum Bearing Kit

DRYER FRONT BEARING WHITE 2PK

Ken from Westminster, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Squeaky dryer

I followed the YouTube video and it gave me step by step instructions however I really needed to replace my dryer slides to fix the problem.

Parts Used:

Dryer Rear Drum Bearing Kit

Shelly from MURFREESBORO, TN
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

BELT SQUEAKING

TOOK OFF TOP AND FRONT PANEL REACHED IN UNDER TUBE AND REMOVED FROM BELT TENSIONER HARDEST PART IS PUTTING BACK ON TENSIONER TAKES TWO HANDS LAYING ON YOUR BELLY

Parts Used:

Al from CORP CHRISTI, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt out bulb

Used a flash light to see, reached in and installed new bulb above the door

Parts Used:

Jeffry from ROCKVILLE, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer needed a new dryer belt

I followed the directions I found on my tablet on youtube.

Parts Used:

Cindy from EPHRATA, PA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bulb was intermittently working

Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.

Parts Used:

Peter from LEOMINSTER, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

There was screeching noise during the drying cycle. Clothes being dried were getting stuck in the upper bearing.

I followed the instructions given in the video I watched when ordering the parts. Very easy.

Parts Used:

Top Bearing

DRYER FRONT BEARING WHITE 2PK

Barbara from SICKLERVILLE, NJ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The felt seal came out, and drum slides were cracked

We watched the YouTUbe video of Steve from this site and followed his instructions for how to replace the top bearing on the dryer, and the seal. It went quickly and easily, and his instructions were perfect. It helped that the model in the video matched ours almost exactly.

Parts Used:

Felt Trap Duct