DV306BEW Samsung Dryer - Instructions

I originally called a repair person to come out but that was a total waste of time and money. He removed the front of the dryer claimed there was a dryer sheet causing the problem and put it back together.
Never again!
I watched a youtube video for step by step instructions on how to take the dryer apart.
I took the front door of the dryer off, removed the filter cover and the dryer drum & belt. Removing this was simple and allowed me to see everything I was working on. With the new part in hand, I removed one wire at a time from the non working heat sensor and connected it to the new part. That way I was sure I had the right connections.
I then removed the thermostat making sure to put the new one back in place exactly as the old one.
I then put the drum back in place with the belt securely fastened. I put the cover back on the lint filter and placed the dryer door back on securing it in place. The dryer is now working perfectly. It takes longer to take the dryer apart than to replace the old parts.

See Utube.com

I firstly over-ordered parts. The general guidance is check one part and replace if bad, then check the next, etc. I only wanted to do the disassembly once so I ordered all the parts which were involved with generating heat. Turned out the heater duct assembly came with the thermal fuse and thermistor already installed, in addition to the heating element. Once I had the parts, I watched the video which was identified in my parts order. Then I started disassembly. I put screws from each step into their own little container so there was no mixing them up. Everything went exactly as shown in the video, except for the front panel containing the control board. My dryer was slightly different, but still easy to get out. When I had the drum out, the heater duct assemble was easy to remove, one screw only. I transferred connecters from the old duct to the new one-at-a-time to make sure there were no mistakes, then installed the new one with the single screw. Re-assembly went quickly. I plugged it in and, with some hesitation, set it to a short timed cycle and started it. After a few minutes, I hit pause and stuck my hand in the drum and it was warm! The dryer has continued to work since. Repair successful!

Thank you
partselect.com for a much better heavy duty belt than the original. Way over priced, but well worth it. After watching the video & following it step-by-step, I now have a perfectly running dryer. P.S. don't forget to plug back in the (3) wire harnesses. The entire experience was a great feeling of accomplishment. Thanks again partselect.com

Followed the video on the website and finished it in a short time. Now it works like a new dryer.

Follow the video instructions.

Unplugged the dryer for safety. Unattached top of dryer from door with putty tool. Took front of dryer off. Unplugged door. Took off bracket to heating element case. Pulled out case. Replaced the thermostat. Then put all back together and tested the dryer. Works like a charm.

replace Drum support roller & axel and belt

The design of my dryer is a bit different from the video on PartSelect - but it is very close. And if you watch the really good video on PartSelect plus a few others on Youtube you can figure out how Samsung in general designs the different components. You can fix this yourself definitely.

Cost of part to fix - about $50.
Repairman - didn't even ask. Would probably be $300-400.
Cost of replacement $1,000.

I rated the repair "A bit difficult" only because this is the first time I have ever repaired an appliance. If I were to repair this one again, I'd rate it as Easy.

I'm really thankful for the PartSelect video. This makes DIY repairs possible.

Thanks.

Dryer was pretty easy to disassemble. The video helped, especially when re-routing the drive belt. Would definitely but from Parts Select again!

this site is amazing. I went on the website, put my model number in and they had suggestions for what might be the problem. “Dryer making a noise?” Click here. I bought a new tension pulley and belt. I watched the videos on how to replace them and the step by step instructions were spot on. Turns out, the old belt had frayed! I probably didn’t need to replace the tension pulley but I did it anyway. The sound is gone, and I felt like a genius for probably a week or so. The last repairman charge me hundreds of dollars to replace the rollers, but now I know how to do it myself. This site is awesome.

I would like to direct the attention to PartSelect instead of my repair. They were awesome in helping me to get my parts. I had called, a few minutes after the deadline for overnight shipping, the gentleman helping me, pushed the order through and I got my parts the next day, allowing me to repair my dryer. I have ordered several parts, for several different appliances, (all Samsung) and PartSelect has always come through for me. Excellent Customer Service!!
P.S. Don't buy Samsung appliances unless you want to get good at repairing them!

I removed the dryer top and saw that the belt was intact. (I had suspected the belt or something stuck in the exhaust fan or somewhere.) I watched a few youtube videos and took off the rest of the top plates and front door and inner structure that held the barrel. After i inspected and cleaned out the fan blades and exhaust areas, I looked at the pulley rollers (motor and idler rollers). The idler roller looked a little melted and chewed up. I replaced it with the new assembly. Also replaced the belt. Putting the barrel and new belt back on was harder for me than the videos indicated because the spring was very tight and the area to put my hands was small and didn't give me enough leverage. I eventually got someone to give me the third hand pulling the idling roller a little further over and the belt was back on. It didn't take me long to put the whole dryer back together. It is running fine now.

These are not instructions as much as warning that although it is a one-person job, the idler pulley assembly is not as easily manipulated with the barrel there. Doing the fix was straightforward: one screw holds it in place. The men in the videos seemed to have no problem with easily replacing the belt, but I needed help with the tight spring. Perhaps now that I've done it once, I could figure out how to reach around the barrel and yank the roller enough to replace the belt, but with the extra hand it took seconds and was super easy.

I still had to take it apart there was a small sock stuck in the fan that blowes the lent out my wife left the lent filter out one time. Your video was a great help. I'm a mechanic and it was easy thanks Anthony Ratto Tulipbike82@aol.com

Followed video and YouTube most was easy.... put the hooking up the belt took time