EDW2020F01BB General Electric Dishwasher - Instructions

Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nearby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.

First I opened the package and screwed the new dispenser cap into place.

Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

First I turned power to dishwasher off at fuse box.then,removed inside panel inside dishwasher about six screws.examined the control switch assembly and removed two screws that hold it into place.carefully removed two wire housings.Then located the part no.and model no.on the control panel.ordered new part online.The new control panel assembly arrived the next day.Installed it right away.Our dishwasher works as good as new. Thanks

Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!

Remove two front mount screws from counter top
Lower dishwasher floor feets
Pulled electric leads cover and disconnect electric leads
Pulled dishwasher out and leaned on it's back
Sorry missed a step turn off breaker to dishwasher
Removed water line and drain hose
Removed motor/pump using only a socket setup and cross tip screw driver
Installed new motor/pump using same tools as removal
Stand dishwasher back up push back into space and reconnect all item mention in removal
Turn back on breaker
Ops check dishwasher
Done.

I had already removed the screws that hold the inner door piece in place when diagnosing the problem. I snapped the new controller in place, put the 3 or so screws back in that hold it to the door, and replugged the wire harness connections from the power and the Sequencer. I put the inner piece of the door in place and replaced those 5 or so screws and restored power from the breaker box. The dishwasher gave a solid beep while the clean light flashed continuously. No other buttons were responsive and pressing the reset button caused a beep but nothing else. I began to research and diagnose that problem which was leading me to the Sequencer when I realized there was a "rewiring" plug on the controller I replaced that was not on the new controller. The controller which is made by Torisan is a generic part used by many manufacturers. The "rewiring" plug which goes into slot CN5 on the controller circuit card, which has wires that comes out of it and go back into other slots in the plug, is used to get the get the correct "pinout" sequence for GE's use of this generic component. Although I could find no information on this, the continuous beep was telling me there was a wiring problem. I removed the plug from the old controller, put it in CN5 of the new controller and the dishwasher works like a charm.

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

Simply screwed in new cap

Removed seven screws that held the inside panel to door. removed inside panel to work area and cleaned. After carefully observing the position of the old gasket, it was easily removed and the new one but in its place. Replaced the door being careful toalign the handle before tightly securing all seven screws. Repair worked, no more leak.

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.

Pulled unit out of cabinet took two top screws out of spinner spray arm and put back together.Old sprayer was plugged up not letting wash go through.Thanks for helping me fix and not replace unit.Saved at least 400.

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

Turned off electical and water - took fillter screen out of inside, unscrewed cap took out valve and replaced it