EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Keep typing for more specific results...

ELFG7437AW0 Frigidaire Dryer - Overview

Sections of the ELFG7437AW0

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
M-Series Ignition Coil Kit – Part Number: 5303931775
M-Series Ignition Coil Kit
★★★★★
★★★★★
(24)
PartSelect #: PS470049
Manufacturer #: 5303931775
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the ...
$23.95
  In Stock
Order now and your part arrives in 2-3 business days!
Screw – Part Number: 131302800
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$21.95
  In Stock
Order now and your part arrives in 2-3 business days!
SCREW – Part Number: 131168200
SCREW
PartSelect #: PS417085
Manufacturer #: 131168200
Sold individually.
$22.95
  In Stock
Order now and your part arrives in 2-3 business days!
Flame Sensor – Part Number: 5303281135
Flame Sensor
★★★★★
★★★★★
(4)
PartSelect #: PS459818
Manufacturer #: 5303281135
This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer is not giving off eno...
$38.95
  In Stock
Order now and your part arrives in 2-3 business days!
Belt – Part Number: 134719300
Belt
★★★★★
★★★★★
(3)
PartSelect #: PS2349294
Manufacturer #: 134719300
This dryer belt is one of the most important parts in a dryer and is what allows the dryer drum to spin/rotate. If the dryer belt is damaged or broken, the drum will not spin or will have difficulty i...
75% OFF
$13.49
$53.71
  In Stock
Order now and your part arrives in 2-3 business days!
High Temperature Adhesive – Part Number: 5308027429
High Temperature Adhesive
PartSelect #: PS474458
Manufacturer #: 5308027429
This high temperature adhesive is used for installing felt and rubber seals on dryers. The tube contains 1 ounce of product. This adhesive is made to withstand extremely hot temperatures. Before apply...
$49.95
  In Stock
Order now and your part arrives in 2-3 business days!
Drum Roller – Part Number: 5304523152
Drum Roller
PartSelect #: PS12741852
Manufacturer #: 5304523152
Dryer drum rollers are parts that support the dryer drum. They allow the drum to rotate smoothly and cut down on the friction between the drum and the dryer frame. They are usually made of metal or pl...
$34.95
  In Stock
Order now and your part arrives in 2-3 business days!
Thermal Fuse – Part Number: 134711401
Thermal Fuse
★★★★★
★★★★★
(3)
PartSelect #: PS4704883
Manufacturer #: 134711401
$34.95
  In Stock
Order now and your part arrives in 2-3 business days!
Thermal Fuse – Part Number: 137539200
Thermal Fuse
★★★★★
★★★★★
(5)
PartSelect #: PS7783961
Manufacturer #: 137539200
$30.95
  In Stock
Order now and your part arrives in 2-3 business days!
Lint Filter Assembly – Part Number: 5304529766
Lint Filter Assembly
★★★★★
★★★★★
(4)
PartSelect #: PS16620745
Manufacturer #: 5304529766
Lint filter assembly. Part has been redesigned. If you are replacing this filter you may also need to replace grille as well. Please see model diagram for correct grille.
$72.95
  In Stock
Order now and your part arrives in 2-3 business days!
MOTOR – Part Number: 5304529782
MOTOR
★★★★★
★★★★★
(2)
PartSelect #: PS16620747
Manufacturer #: 5304529782
This drive motor includes the pulley for the dryer drum belt. The motor has reverse threads for the blower wheel. Please disconnect the power before starting your repair. This is a genuine OEM part.
$168.76
  In Stock
Order now and your part arrives in 2-3 business days!
Idler Arm Spring – Part Number: 131601000
Idler Arm Spring
★★★★★
★★★★★
(1)
PartSelect #: PS418263
Manufacturer #: 131601000
Revitalize your dryer with the genuine OEM idler arm spring idler pulley spring from Frigidaire. Expertly crafted to keep the idler pulley tight against the drum belt, this part facilitates smooth and...
$50.44
  In Stock
Order now and your part arrives in 2-3 business days!

Questions And Answers for ELFG7437AW0

Be the first to ask our experts a question about this model!

Common Symptoms of the ELFG7437AW0

[Viewing 4 of 4]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing
Show All
Not Heating
Fixed by
these parts
Fixing Fixing Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would heat initially then cool down
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
Parts Used:
M-Series Ignition Coil Kit
  • Brett from Monticello, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
97 of 110 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy Dryer
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
Parts Used:
Belt Drum Roller
  • Philip from Oakland, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
55 of 67 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would heat only on the initial start. Burner would not light again until completely cooled down. The ignitor would energize, but no gas would flow for ignition.
1. Pry Dryer top up and off the clips. (Front of Dryer)
2. Remove 2 phillips screws on the inside of front panel.
3. Lift front panel up and set off to the side
4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place.
5. Unplugged and removed both coils, installed new coils and bracket. Re installed front panel, screws and top.
Parts Used:
M-Series Ignition Coil Kit
  • Bruce from Burnsville, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
41 of 50 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!