FGSC2335TDA Frigidaire Refrigerator - Instructions

When removing existing filter you will experience some resistance at the 10-4 position which requires a little extra pressure to reach the 9-3 position.

We followed the video instructions and it went fairly smooth. After turning off the water at the street we found that the faucet at the wall had it's own "on/off" valve. When finished, we turned on the power and heard the gears going through their revolutions, but no ice was made. We waited 24 hours and still no ice. I removed the cover on the ice maker and adjusted the amount of water to see if that was malfunctioning. Still no ice was created. Waited another 24 hours - nothing. Waited another 24 hours (the site said that sometimes the ice maker would take time to reset itself) - nothing. Then on the fourth day after changing out the triple water valve we heard water being dispensed and later that day it put out the first ice in weeks. Another hour later another batch of ice cubes were ready and deposited into the bin. Since that time, we have had a full bin. I moved the set screw back to it's original setting because a little too much water was being delivered. The cubes weren't separating to individual cubes. That cleared up the problem. This was easily completed - we recommend others do their own work. Just be patient for the system to reset itself.

This is the second time I've had to replace the crisper cover, so I had that step mastered. As before, I took the glass from broken crisper cover and dropped it into new cover in seconds. Had to use a screwdriver to pry old crisper supports from the walls of the fridge. This was the only hassle. Popped new supports in, replaced crisper covers, and slid crisper drawers back into place. From now on, I'll have to be more careful about how much weight I put into crispers.

Went to oartselect.com located diagram and part. Took out ice drawer to prevent ice being dispensed. Remove small front panel in door for ice- water & cubes, 2 square tip screws on top. Remove small grey panel, 2 Philips head screws, remove ice dispenser unit 2 Philips screws, unplug 1 wire connector.
Insert ice dispenser unit from partselect.com, connect wire connector, screw in 2 Philips head screws, place cover panel in position and screw in 2 Philips head screws, place small grey panel in position and screw in 2 square tip screws. Put ice drawer tray back in refrigerator, try water, try crushed ice, try cubes. FINISHED, just saved yourself a couple of hundred dollars in less than an hour. My wife said she could do it after watching how easy it was.

I ordered a new shelf and I put in, less than minute

Looked at video on how to remove and reinstall support and followed the instruct ions

Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

Popped out glass, pulled up and the front of cover and pulled froward. Pushed new cover back on to studs and pushed down on cover to lock it to front studs. Put glass on top of new cover. About 3 min total to make repair.

REPLACED WITH NEW.
HOWEVER, THE WATER FILTER INDICATOR STILL SAYS
'REPLACE'. THERE IS NO LEAKAGE, BUT IT APPEARS LIKE THE NEW CARTRIDGE IS NOT COMPLETELY INSERTED. I'VE TRIED REMOVING AND REPLACING THE NEW CARTRIDGE SEVERAL TIMES, BUT IT STILL SAYS 'REPLACE'.
INCIDENTALLY, THIS WAS THE SECOND ORDER OF THE CARTRIDGE AND LAST TIME I GOT TWO, AND THEY BOTH FIT FINE! WITH THIS ORDER I GOT JUST ONE.

The line for the water to the door was too short to install. Lacked about 4-6”Ice maker line was fine.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Replaced the Triple Water Valve

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure