GDWT358V00ES General Electric Dishwasher - Instructions

delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.

Pulled off old rollers and snapped on new ones. Never easier!

Wheels and axles come separately and no instructions were included. After a few minutes of looking at the parts, I realized you have to put the axles on the wheels and then snap it on the dish rack. Once I did the first one, the others were easy. Made my dishwasher feel like it was new. Obviously the design of the original wheels was faulty as these were a different design.

It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!

I watched the video that came with email on part. Gave instructions on how to. Thank you !

pulled off all old rollers and axiies and snapped on new ones

Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.

Put new basket in, threw old one away

Ordered new cap and put it on when it arrived.
Simple

went online to parts select. Looked at parts that could be leaking. Thought it was the sump. Purchased the sump and the pump connector. Almost bought the adaptor pump assembly, but it was $29.00. Parts arrived in about 2 days. Turned off water and power to dishwasher. Disconnected the copper water line. Hardest part was getting the dishwasher out of space. Once out, layed it on it's side. Parts held together with clamps. Took it apart like a puzzle. Replaced the parts, tightened the clamps. Pump connector hard to unscrew. Got a good hand grip on it and turned it loose. Sump did have a hole in it. Put everything back together. water, electric, etc. Turned it on and it was leaking. Leak coming from the adaptor pump assembly. Couldn't wait 2 more days.Found part at a local parts store for $40.00. Was able to change it by reaching underneath and not pulling dishwasher out again. All three parts needed to be changed. Dishwasher now working fine. If your leaking underneath and taking out the dishwasher change those 3 parts.

The old wheels and attachment brackets were easily removed since they were always falling off. I ordered all new brackets and wheels, but it turns out I didn't need new wheels. If your original wheels are in good condition, they are the same size as the new ones and fit the new brackets. The new attachment brackets are built differently than the ones that came with the dishwasher, but (a good thing considering the originals only lasted 1 1/2 years). The new brackets and wheels snapped together and snapped into place on the dishwasher in minutes--no tools were needed. It took longer to cut the parts out of the packaging than to install them. The bottom rack now rolls out like it did when it was brand new. Definitely worth the few dollars in parts.

I placed the missing cap into the dispenser.

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.

The sump was very clogged with caulk like crud that we think was a chemical reaction from soap that was used the first two years. When I first started troubleshooting, the sump seemed to be the problem, so I replaced that. There was a small hose on the sump that was broken so it made sense to replace it anyhow.

When that didn't help I put the dishwasher into service mode and observed that there just wasn't enough water to spin the sprayer. Therefore it was a water quantity problem, which can be caused by either the Water Inlet Valve or the Flood Switch.

I ordered both the Water Inlet Valve and the Flood Switch, just in case. I replaced the valve first and when that worked I did not install the switch.

Installation was performed with the dishwasher still inserted in the cabinet. If you have big hands, pull the dishwasher out. With sockets and nut drivers, I was able to remove the assembly. After pulling it out enough to clear the dishwasher, I was able to get a screwdriver on the outlet side clamp and a wrench on the inlet side hose.

My old valve had a 90° elbow on it and that was difficult to remove. Installing the elbow on the new valve was just as bad. The valves don't have enough clearance to get a wrench on them to keep them from turning while the elbow is tightened.

TIP: Take a picture of the valve before removing/disconnecting anything. I don't know if the electrical connector can attach either way but I made sure to put it back on exactly the same way it was.

Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.