GI5FSAXVY01 Whirlpool Refrigerator - Instructions

Replaced mullion and pivot block
The pivot block and the mullion showed signs of wear and tear where they would meet up to close the left door.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

one screw and electric plug and the unit slide out. Slide the new one in and your ready to go.

Layer it out for 24 hrs used hairdryer on med for the wrenkles.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

Googled "intermittent clicking noise" or something similar and consensus was it was either the capacitor or compressor start relay. You-tubed videos on how to replace these. Looked easy. Just unplug them from the condenser and replace. Contacted Part Select and staff said 50% of the the time it was the capacitor, 50% of the time it was the relay. I was in a time crunch so I ordered both and they came in a couple of days. I replaced the capacitor but the clicking noise continued. I replaced the relay and problem solved! Maybe I could have gotten away with just replacing the relay, but I had them both by then and figured with a 10 year old fridge, better replace them both at the same time and be done with the problem. So far, so good.

I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Prior to ordering I removed freezer panel and checked for ice build up and fan functionality. Then removed rear panel cleaned lint from everything pulled front panel vacuumed out the condenser. Plugged back in and all seems to work with the exception of compressor. I have a little experience so googled in model number and your site popped up. I looked up part and the site gave me a percentage loved that. I ordered wish I would have rushed shipping as took about 10 days. Installed in less than 30 minutes and all runs great ??

Let the ice in the freezer melt while installing P trap drain tube

Saw U tube instrctions how to install and it was easy

Open and remove door by loosening two screws on both sides of the door. Lift up and away the door.place the door on flat surface, grab and lift up on seal pulling out of reach. Clean track, alone seal on food before pressing in place. Check to make sure seal is set in place. Install door job done.

Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars