GI7FVCXWY02 Whirlpool Refrigerator - Instructions

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed

Online parts detail made identifiying the correct part very easy. $10 fix instead of a $150 service call. Once the right part was identified, fixing it was very easy.

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

Unscrew filter. Screw on filter bypass

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Layer it out for 24 hrs used hairdryer on med for the wrenkles.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

I ordered the wrong part for my refrigerator. The refund processed easily. However, the email that I was promised with return instructions has not been sent. I have asked several times about how to return this part and total silence from partselect. I'm ready to throw this replacement bin in the trash.

Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.

Removed old shelf and installed new shelf. No tools required

Let the ice in the freezer melt while installing P trap drain tube

Simple. Just put it on the racks provided in the fridge. The part fit perfectly and took literally 5 seconds to put it on.

Open and remove door by loosening two screws on both sides of the door. Lift up and away the door.place the door on flat surface, grab and lift up on seal pulling out of reach. Clean track, alone seal on food before pressing in place. Check to make sure seal is set in place. Install door job done.