GLD4408R00BB General Electric Dishwasher - Instructions

When I first tried to fix the handle I could not figure out where the spring went. I went back online and looked at the diagram of the dishwasher on this site and learned where it went. Once I knew where every piece went it only took me about 5 minutes to put it back in and another 5 minutes to screw the cover back on. I am a newer homeowner and want to be able to do minor fixes. This was my first one and was very happy that I was able to do it on my own.

I replaced the broken/cracked soap and Jet Dry dispenser (i.e. MODULE RINSE AND CAP ASM - part #PS1481889). (Water was leaking into the soap holder and hardening the soap into a lump before the door would open, rendering the soad useless).

Steps:

1) Unplugged the dishwasher.
2) Unscrewed the 6 screws holding the front stainless steel panel to the plastic door; set aside panel and insulation.
3) Unplugged two wires from small electric motor in broken ASM.
4) Unscrewed 6 screws holding ASM in place; easily slid out of door.
5) Slid in replacement ASM and put 6 screws back in (tightened snugly to make slightly warped door bend to new ASM).
6) Plug back in two wires into new ASM.
7) Re-attached stainless steel cover to door (having a 2nd person hold this in place while screwing would've helped).

All done - works like a charm! No more dirty dishes because the soap didn't work right...

Bottom line: If you have a phillips head screwdriver, you can do this repair. Easy to do.

Unscrew supply tube and angle nut from old valve. Disconnect tube from valve. Install new valve. Obtain new crimp seal for water supply tube. Use Teflon tape. Reconnect water tube to valve.

1. remove old basket. 2 Place new basket.. Done

The repairman diagnosed the problem as a control board failure and quoted a $350 bill. I self-diagnosed it as a failed interlock switch -- and found out that the switch was OK but the cover was cracked, preventing the switch from functioning normally. Total repair bill - $1.50!

Installing the gasket took about 45 seconds. It actually took more time to scrub the area clean prior to installing. One quick trick I found was to fold the replacement gasket in two, and use that mark to center the gasket and press it in from there. That way you don't have any guesswork as to how much slack to allow for when starting.

Disconnect electrical power & shut off water supply. Remove front panel covers. Removed mounting screws (2). Unhooked water supply line & flow line. Took off old brass adapter fitting. Teflon taped fitting to new inlet. Performed reverse procedures. It ran just fine!!

I pulled out the racks and decided to take off the upper (mid) arm. It came off with an adjustable wrench. When I looked at the arm I could tell that some of the holes were blocked. Some debris had gotten lodged in the holes and were blocking the water flow. I used tweezers to remove the debris and it solved the problem. I then pulled out the lower arm and cleaned it with warm water. There were soap deposits and I wondered if other debris could be blocking this as well. Finally I went onto the web site and saw that for $40 including shipping I could replace these parts with brand new parts. I did and the machine washes like new again.

Took screws out of door. Slid bottom seal off and slid new one on.

The repair was really easy. I ordered the part needed after looking at this website. I figured out the problem by looking into the forums. I ordered the part. It came within several days. I got home from work and after dinner pulled the dishwasher from under the kitchen counter. It was easy to do. I flipped the dishwasher on its side. Then removed the old part. It had a water inlet that required a fitting to be loosened with a wrench. It also had a flexible water fill that was attached with a cable clamp. (Remember to turn your water supply off first!) The wiring was disconnected by a simple harness. Four bolts had to be removed to pull the part off of the dishwasher body.

Installation was the reverse of this process. Have been using for a week now and the problem is corrected. Doing business with Parts Select is awesome. I know that over the last several years I have saved tons of money and learned that I can fix nearly any appliance by viewing this website.

Everything snapped on quite easily. I was releaved to not have to replace "everything."

I found that the supplied part did not have threads to receive the bolts that were used in the original part. I had to locate thin nuts and bolts and very awkwardly fit those in behind the part. The orignal part would have just bolted on from the front. I almost returned the part as unsatifactory, but decided to make do. Otherwise it would have been a 10 min job.

Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

I took the front off of the dishwasher door, loosened the screws, unplugged the module and replaced it with the new module. This repair was the easiest repair I've ever completed!