GSD2001J20BB General Electric Dishwasher - Instructions

The hardest part was removing the dishwasher from under the counter and cleaning up the large amount of water that poured out when I turned the unit on its side.
The actual pump replacement was pretty easy except there were a lot of extra parts that were only needed for other brands or other models.
I might have tightened one of the large clamps too much as there was a very slight leak after I was done. One or two drops of water per cycle, which evaporates quickly and not worth taking apart again.
It was not hard but took longer than predicted.
Much better than buying a new dishwasher or paying the estimated $350 to an appliance repair company.

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.

Rather than remove the dishwasher from the counter, I performed the repair inplace, which was much less work (although I did have to lay on the floor).
After turning off the power, I removed the two access panels at the bottom of the unit, disconnected the wiring from the pump and solenoid, loosened the drain hose fitting and drained most of the water out of the unit and into a shallow pan (the drain solenoid was stuck open, so this was pretty easy - otherwise, I still could have manually actuated the drain valve & solenoid to drain water through this hose).
There was alot of water in the unit and my pan overflowed a little. If I was doing this again, think I would have disconnected the drain hose from under the sink and drained out through that into a bucket (I could have controlled that flow better).
Once the water was out, there are just two hose clamps that hold the pump onto the unit (one on top and one in the back), and a stabilizer bar that connects the motor to the front frame. Removed these and the whole unit came right out.
The replacement pump & motor was exactly the same as the one that came out, so I didn't need any of the hose or wire adapters that came in the kit.
Reconnected the two pump connections, motor bracket and wiring, and the unit was good-to-go!

I cut the water off to the DW, unscrewed the water connection to the inlet valve, unplugged the electric connection, disconnected the black rubber line from the valve to the washer, removed the 2 screws holding the valve in place. Put the new valve on by doing the above backwards. I also used white thread tape on any connections that needed it.

Actually, the problem started with a Timer Motor failure, and that let the dishwasher run for 4 hours (doh!). Immediately, I tested and ordered the timer, which unfortunately didn't come as just a motor, it came as an assembly. I installed it, and the dishwasher ran the cycle just fine.

Except it didn't drain.

After poking around, I noticed the drain solenoid had apparently been overworked; the timer must have failed on DRAIN. The solenoid was severely overheated, and thankfully didn't cause a fire, but it was somewhat melted. Replaced the solenoid, and all is well, especially when my wife was eyeballing a $1000 Bosch!

I received my dishwasher as a hand me down, my Aunt never liked the way it cleaned. After it sitting for about 2 years i installed it in my house and found that it leaked all the time from where motor shaft went into the pump housing. After disassembling everything and scouring parts sites online, I found the parts, ordered them. 3 days later i had the parts, and the next day I had a fully functioning leak free dishwasher.

This is a great website. I ordered my part on Wednesday night and it arrived Saturday morning without paying any extra for shipping. Plus since I am a female, this website enabled me to easily and affordably make the repair myself without having to worry about a repair man trying to take advantage of someone that they think they can.

I first made sure that there was nothing stuck in the drain area inside of the dishwasher. That meant I had to bail out all the standing water and then unscrew the mesh cover from the bottom. Since there was nothing in there I ordered a new solenoid.

First I unplugged the dishwasher. Then I removed the screws with a screwdriver that held the bottom cover on the dishwasher. Once I could see the installed solenoid, I put together the pieces of the replacement solenoid that I bought so I was sure to install the new one correctly. That did not require any tools. Then I unscrewed the two screws that held the solenoid in place and removed the little metal ring from the shaft which was the last piece holding it in place. Getting that ring off was tricky. I ended up using a pair of tweezers to pull it off. After that I put the new part on and screwed it in with the two screws provided. The little metal ring went on much easier than the old one came off. I screwed the bottom cover back on and voila! my dishwasher was fixed.

Unscrew supply tube and angle nut from old valve. Disconnect tube from valve. Install new valve. Obtain new crimp seal for water supply tube. Use Teflon tape. Reconnect water tube to valve.

First I took out the two screws that hold the drain solenoid on the unit and took off the c- clip that held the arm on the shaft if you have a digital camera take a picture to make sure you can get it back together the same way.. Then put together new unit and attatched putting the c-clip back on. Ran it through some cycles to make sure the solenoid was working. Four days later the solenoid is melted again, the timer must have an intermittentant problem I should have replaced the timer and the soleniod both at the same time. Make sure you dont make the same mistake I did. Now I will be buying a new dishwasher instead of putting any more time and money into this one.

first, I removed the screws holding the dishwasher to the countertop.Then I removed the dishwasher from under the counter. I turned the dishwasher on it's back and loosened the three hose clamps securing the water connections to the pump assembly. I then removed the electrical plug to the motor and the screw holding the support rod to the motor. Then I worked the loosened water connections apart and removed the pump and motor assembly.
Then I removed the hose clamp and plug from one of the orifices on the new pump, and aligned all of the water connections and wiggled the new pump assembly into place. I tightened the hose clamps, Installed the new screw and support bar to the motor, and connected the electrical plug. I then turned the dishwasher upright, reconnected the power cord, water supply and drain lines and started a wash cycle to check the new system for leaks. I found that the extraneous drain solenoid that came attached to the new pump was loose and rattling, so I secured the solenoid shaft and linkage to the pump housing with electrical tape to stop the rattling.

I received panels about week after I ordered them, however the large panel came scratched. I immediately called your customer service who was extremely helpful and considerate. She ordered me a replacement and it arrived the very next day..

Excellent service, I was truly impressed.

Removed the dishwasher, turned it over, removed 3 hoses, 2 clamps, 2 wires and one support. Installed new pump and reconnected. Done!

Shut off circuit breaker to dishwasher and shut off valve to dishwasher under sink.Remove bottom access panel screws on both sides of panel. Remove both screws holding dishwasher to counter.Place old mattboard strips under legs to prevent scratching floor & slide out from under counter. Use a Shopvac to remove water and spillage. Have rags and paper towels handy. Carefully disconnect wires, drain hose and water line to free dishwasher. Fold old rug runner in half to place dishwasher on, turn on side and then gently upside down on rug to access motor. Remove butterfly clamps, hose clamps, electrical connections, and support bracket. remove old motor and pump and place in box to discard. Position replacement motor and pump according to diagrams. Reconnect all clips, hoses and connections. Since replacement motor and pump is smaller, use longer support bracket from adapter kit. Return dishwasher to upright position and reconnect wiring using wirenuts, drain hose and waterline. Reposition mattboard strips under legs and slide back into place. Attach screws to counter top. Turn on power, water and do a test run to check for leakage. Replace bottom access panel. Pat yourself on the back since you've saved yourself hundreds of dollars for a repair or replacement of your dishwasher.

Removed built-in washer and turned on side. Removed complete motor and pump to work on bench (easier). Removed pump and replaced with new unit. Instructions did not tell what to do with white plastic tube for shaft(goes with lip facing motor onto shaft)Be sure rubber seal is pressed into pump fully. Inch pound instructions were not helpful. Remember how much pressure it took to take off it helps to install new pump. Inch pounds is not what most people know or use. Reassemble unit, flipped on end and tested for leaks before replacing under cabinet.

Disconnect electrical power & shut off water supply. Remove front panel covers. Removed mounting screws (2). Unhooked water supply line & flow line. Took off old brass adapter fitting. Teflon taped fitting to new inlet. Performed reverse procedures. It ran just fine!!