GSG25MIMBFWW General Electric Refrigerator - Instructions

Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.

Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.

This was a simple repair. I removed the broken bin from the refrigerator and snapped the white plastic handle / humidity control slide off the broken bin and snapped it onto the new bin. I replaced the bin in the refrigerator and loaded it up with veggies. Took all of 5 minutes to make the repair.

Undid the three screws (one just held the light, which had to be detached but not removed from the refer), cut the lines several inches up, and removed the old reservoir. No quick connects came w/the part, and 5/16" items are not available in most stores, including Home Depot, Lowes, Ace, True Value, etc, so had to order separately on line (search 5/16" quick connect) (another $12 with S&H). Don't use a pinching type tool to cut the lines - not a smooth cut. I used a miniature pipe cutter I happened to have because I am a hobbyist. Cut the lines on the new reservoir at same place as old one, pushed the quick connects on, pushed the QCs on the lines sticking out of the refer, replaced screws, and was done. Quick connects should be included with this part.

The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!

There is no access to the inside of the door to replace the water line. I was able to insert a 1/4" drip line barbed connector into the old line at the base of the door and then connect that to a piece of the plastic tubing which I then connected back to the original water supply tubing with the 5/16" union. It took three attempts to get the tubing through the bottom hinge without a crimp in it. It's best to have a second person to hold the door while you "fish" the tubing through the hinge.

They don't make appliances like they used to. When my little butter door cracked, we kept using it until it finally fell off for good. So, where do you buy one of these? When I turned to the internet, I found a few places but they were toooo expensive. PartSelect had the right part at the right price. I figured that if I bought another little damaged part, the light cover, at the same time, the shipping cost was essentially halved, an even better deal. I was so surprised when my parts arrived faster than I expected, a couple of days by regular mail. That's faster than I could ever get a service call and who's going to call a repairman for a simple thing like that, anyway. If not for PartSelect my reputation as the Queen of Duct Tape would still be intact. I didn't want duct tape holding together my newish SS fridge in my redone kitchen. Imagine tile, granite, stainless and duct tapeI placed the little door in the fridge and now the butter stays put. the lower light shield is just as easy.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

the only thing I had to do was slide the shelf in.. but this website saved me over $50 on the part (I got a price from my local appliance store of $80.00 and 2 weeks to get it)

It originally appeared that an easy out would be required to remove ferule from piping line, but later it became necessary to cut old broken fitting off and replace with compression fitting in replacement kit. Total time to repair after all tools were on hand (needed to buy tubing cuter) was about 45 minutes.

Remove rear plate. Remove fan bracket. Replace fan gaskets, blade and motor. Replace bracket. Replace rear plate. Very simple. Fixed the problem.

pulled out broken bucket and auger assy. and slid in the replacement. works great so far. The easiest part was ordering the part and it didn't take very long at all to get it. Customer Service was very good at getting the job done. Thanks

I tried to quite the noisey evap motor with special liquid motor grease from Radio Shack. It did not work, so I ordered the evap motor. My freezer motor was wired slightly different than the motor I received. The replacement motor had a male plug attached to the four wires, the original motor was different, so I cut the wires and spliced them into the original freezer wires (colors were the same). Remounted motor. Works great, and no more groaning motor
Peter