GTE16CBCBRWW General Electric Refrigerator - Instructions

I opened the refrigator door and inserted the shelf where the missing one shoud have went and I remoed the old Vegetable bin cover and replaced it with the new one.-----JOB DONE !

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.

10 minutes total.

The best part was ease of ordering and next day delivery! The install was a no-brainer. I was more than impressed with the ease of access to the parts and speed of delivery.

I pull the old one out, and put the new one in.

After looking at our broken bottom shelf in the fridge many times a day for over a year, I finally got around to doing something about it. So glad that I did! First of all, the part was shipped amazingly quickly. I had it within two days (at regular shipping). Secondly, it was a cinch to install. What a world of difference!
The only caveat is that the new shelf fits quite snugly. If you don't give the refrigerator door an extra push to close it, the door does not seal. Just a new habit we have to get into.

At this time of the year our beach fridge is always full of food and drinks. Every time we want something it meant leaving the door open for extended time whlie moving things left, right and center. When the new shelf arrived I removed the food and drinks from the existing two shelves and moved them closer together. I then slipped in the new shelf and reloaded the food. Suffice to say the fridge stays open less and we are able to get at things without moving others. I wish I had thought to do this before.

I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The fridge works as good as new. Thanks a ton!

Remove the fridge door and put it on the floor. Being able to apply lots of pressure helped get it into the tight groove. The corners were the hardest part. This requires strong "man" hands!

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

first I ordered parts that didn't work. the return process was painless and I found the part I needed, which just popped right in!

My repair was simple. Just put the shelf in the holes in the freezer. The AMAZING thing was how quickly I recieved the part after placing my order. I placed the order at about 3:30 pm on a friday checked the box for ground shipping and the part was at my door the next morning. I think that was a mistake, but I was impressed.

After reading the trouble shooting section of the owners manual, I determined, without much difficulty, that the temp control was defective. I checked some local outlets and found the prices running from $36.00 and up. The same part from this site was around $20.00. Guess where I bought mine! It arrived in a timely fashion, and I installed it with no problem, in about 10 - 15 minutes. This was a very easy job, just remove and replace three wires snap the unit into place, and screw the cover on. Tip: I always use you tube or another source to get some instruction, just in case I'm not as smart as I think I am!

Went on YouTube and it had excellent instructions for removal and installation

Shelf cracked when less than year old. and has gotten progressively worse thru the years.
Replaced in seconds , no tools required .
I should have done this years ago

The hardest part of the repair was emptying the freezer, next was getting the fan off of the motor shaft, The only reason the job was difficult is because i am 67 years old and not as flexible as i used to be.I had a tough time getting the fan off of the motor shaft, but i got it off with the use of a vise, and had to use the hammer and a socket to install a new fan blade.