GTW525ACP1WB General Electric Washer - Instructions

Took off belt/motor housing and replaced belt. Put housing back on. Very easy.

Removed the center agitator to clean it - had black mold and pink soap scum buildup underneath that you couldn't see or clean without taking it apart. Removed the bolt with ease. Upon tightening the bolt back in place, the bolt sheared in half, leaving the lower half threaded in place and the head in the socket. Had to use a drill bit and drill out the lower half of the bolt completely. Ordered the replacement bolt and reassembled everything in less than 5 minutes. Replacement part was perfect - hopefully it lasts longer than the original bolt.

I contacted parts select and entered washer information and asked them if they thought they would now what the problem was and and they responded with a answer and also a list of two parts that they thought might take care of the problem. I ordered the parts,looked on u tube to see how to change them and replaced both parts .I think the clutch was good but the drive belt was stretched and needed replaced.Know it works great.

Unplugged washer and hoses. Removed 4 screws in back control panel and 4 screws holding control panel down. Drained capacitor and checked that. It was good. Pryed washer top off with screw driver. Used vice grips to remove old and install new spring rods, replacing them one at a time. While lid was off I cut a small diameter pool noodle in half and cut 4 half noodles the size of each side. I unclipped one side of the tub cap and ran an 11" zip tie through the hole in the middle of one side and back up and out where the tub skirt and cap meet, then tied the half noodle to the edge of the tub cap and snapped down cap. Then repeated with the other three sides. I did this so heavier clothes, if they got out of balance, would continue to spin. The noodles keeping the tub from moving too far out of balance. The rod springs helped with lighter loads but still shut down spinning with heavy clothes. The machine always handled heavy clothes for 7 years until the last month or so. If it breaks with the noodles, I'll get another new machine.

You have to take the top off of the washer and the four suspension rods are at each corner. Fairly simple removal and installation of the rods. A quick you tube search is all it took. Easy peasy.

There's two nuts on the back of the washer holding the metal backplate. I used my 11-1 Klein screwdriver. Once you get the screws out lift the backplate slightly and pull the whole top assembly out of it's spot and lean it forward onto top of the washer.

Take pictures of where the wires go so you can remember for later.

Disconnect the two wires and remove the two screws holding the metal plate. Same size nuts driver as the other screws.

Remove the sensor by just wiggling it out.
Slide the intake assemby out of it's spot.
Slide the new one in.
Then just do everything you did in reverse.

Takes 10 minutes. Super easy.

IF you do the same repair, SAVE THE LITTLE O-RING that is inside the old part where the temperature probe stick in (If that is indeed what it is). It's chrome in color. New part does NOT come with that O-ring

Extremely easy. You will need a helper to make it easy. The best directions are on you tube.

one bolt off pulled agitator one bolt on

Being a woman I had to figure out tipping it in its front. I put it on a dollie and drop it down real easy.
Removed all water lines after water was shut off.
Removed bolts. Removed bolts on plate to the right to unplug old pump.
Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm and I saved $408 by doing it myself!!!!!

Replaced water pump. Washer now works as new.
Wife is now happy!

I ordered a drive belt later to go with this repair which I wish I had done when I ordered the speed sensor and saved shipping. I think that was the real culprit. I had get customer service to help me with the part number because it wasn't listed on the parts list.

I set washer to drain and spin empty to get as much water out as possible. Tilted washer on its side on top of two thick cushions so was about a 15 degree angle off the floor and didn't spill leftover water in the drum.
I took the protective cover off using socket wrench for the 3 bolts. There was belt shreds all over the bottom. Took off smaller drive wheel with socket wrench in order to get to speed sensor. Speed sensor is connected on the motor frame. I used two small flathead screwdrivers in the slots to unsnap the old part. Cleaned off belt debris. Connected the new speed sensor wires first then should click into place. Put drive wheel back on. Put new belt on small drive wheel and lined up grooves. Note that the new drive belt will be smaller than the old one. I found the easiest way to get the new belt on is to hold it on the small wheel and start wrapping the belt on one side of the large wheel and rotating the wheels which is going to turn the drum. Sort of how you would rechain a bike which shows my age!
Put protective cover back on.

The last thing I did was since I had access to the bottom of the drum was to clean out the pressure line port which can lead to spin issues. It is about half an arms length up the side of drum above the drain hose. Its a small gray tubing attached to the drum. Pull the tubing off and it reveals a little port that can get clogged. Use your1/16th drill bit and put in the port about an inch to inch and half and clear out the port. Re-attach the hose firmly.

Machine working as good as new and clothes are almost bone dry now!

1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply.
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!

I watched a youtube video to see how others performed the repair. My washer was a little different than in the videos but the inlet valve was very easy to access once I pulled the washer out of it's "nook". I took off the back panel of the control "box" (4 screws). Then accessed the valve which was held in place with two screws. The screws were buried behind a few wires so they were a little difficult to access but not impossible. I did need to use my 1/4" box end wrench as my son had borrowed my socket set.

The people at PartsSelect were helpful in selecting the right part and the repair is working fine. My wife is happy.

Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.