GTW750CSL1WS General Electric Washer - Instructions

Took 4 screws out of back of control panel. Tested old capacitor. Installed new one. Put back on tested spin cycle everything is doing great

went online to replace water pump on washer site and followed directions. Very easy installment.

Took the belt cover and then replaced the pump. Did a dry run and everything was fine.

Unplugged the machine, pulled it away from the wall, didn’t have to disconnect water lines, set the parts out on the counter as I went over the instructions a couple of times, followed the directions, plugged it back in, worked perfectly again.

The drain pump had three screws. Frist unplug the machine and turn the water off. And unplug the hose for the Hot and Clod Water. Make sure their no water in the tub. Unplug the pipe from the Tub. The unscrew the nut for the connector. Then unplug the connector and be careful not to damage plug for the connector. Press the plug connector with your finger or long nose pliers . Then just hook the new plumb and you all set.

There are two lid clips on the front side of the top and a narrow blade putty knife works great to release the clips. There are 4, 1/4 in hex head screws in the back area of the top, two on each side. Two are in the console and two are under the console.
Pay attention to the orange pressure switch hose, when lifting the Console, can pull this hose off, this hose can be pulled off easily. The lid/lock switch is easy to remove, once the Bezel is removed, then slide the switch to the left it will release. Remove and unplug the harness. The new lid/lock switch clips back in the same manner it was removed. Important! When the new switch arrives it may not look like the old one.

I watched a video on a few times that PartSelect sent me about how to make the switch from the broken lock set to the new one. And it really went just as the video showed. So far things are working.

Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!

any electrical device unplug the power cord. I followed the instructions the best I could understand them. but once the part was removed I took pics from my cell phone of how the wiring ran, and also what other connections I had to undo. all connections were made, connected the hot n cold hoses, plugged into the washer no beeps or sounds as before opened the hot n cold water valves, and the tub was being filled with water. could not turn on the washer, no lights or beeps... so I gave up I spent too much time on this machine and money too, hope to get an RMA for the Lid Switch assembly

Tilt machine back to access pump on bottom of tub. Lay towel down to catch small amount of water. Use pair of pliers to remove clamp from recirculation pump hose. Remove 3 ten millimeter bolts from pump. Then use reverse procedure to install new pump.

Put the parts in, turned washer on.....lid lock still blinks, will not operate. Suggest the control board that sends the signal to the solenoid lid lock switch is defective. Buying a new washer, scrapping this one.

Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well

Watched You Tube and had at it. In the end it was fairly simple.

I replaced the Pump Drain assembly. It was very easy. Removed 3 bolts and disconnected the electrical wire harness and put new one on. It works great.

Lift the cover, undo too screws, Slide out broken part, slide in new part put in the screws and close the lid.A piece of cake.

Thank you for the super fast service on Christmas eve no less!