IUD9500WX4 Whirlpool Dishwasher - Instructions

I removed the 10 screws that hold the front door panel on and then I removed the 6 screws that hold the dispenser in place, pried slightly on the 2 clamps that hold the dispenser in place, unplugged the wire to it and pulled it out.
Put the new one in and reversed the steps. Presto done!
Works great.
Thanks Parts Select.
PS
Kitchen Aide come up with a better design!

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I removed inner face of door, cut wires leading to door switches, and then installed the new door switches and wire harness.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.

I found an exact match to my rinse aid cap on your website and ordered it. It came to my house in 2 days. It fit the dishwasher, and I used it tonight for the first time with the rinse aid. (With the change in detergents, the detergent alone was not leaving the dishes and silverware feeling smooth and clean.) The dishes came out much better tonight.

I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.

Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.

My KitchenAid dishwasher's upper dishrack had several places that were completing rusting out, just leaving the skins of the plastic coating in place. I ordered the upper dishrack - just the dishrack, none of the clips or other items shown in the schematic - and installed it pretty easily. One caution - this is JUST the upper dishrack. If you have two rows of tines that are clipped in and flip-flop back and forth on the left and right wider sides of the rack, you will need to order one or two pieces of part # PS 898500 as well. One of my tine rows was in salvageable shape, so I only needed to order one (in a second order upon discovering I it wasn't included). It wasn't difficult to figure out how the clips could come out and snap back in place. Just be careful, know that these are just plastic items and can break easily.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.

Pulled out dishwasher. Took out old screws. Unsnapped end of rack slid new wheel in and attached to side. Very Very easy. It was great to get the part so fast and take care of this repair ourselves.

I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video

Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com