JBP21BH4WH General Electric Range - Instructions

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

Followed the video and it was fast and quick.

First turn off the breaker, and test with my milti meter. Raise the top panel where the coils are and prop it open high enough to use a screwdriver to open the front panel.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.

took nut driver to remove the old and replaced with new. simple.

First my son removed the two screws that held th element in place but first please tell everyone to turn off the breaker first. My son did not and he had gotten a shock from this and burned his hand. I think this is very important first. After cleaning up his hand he then replaced the element and tested it and it worked nicely.

Thank you for your prompt delivery and the correct part.

Sincerely
Kelly Didsbury

Removed two screws, and replaced element with a new one. Easy, works great.

Open the package and slide the Knobs in place. 30 seconds to place 4 knobs.

0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!

That's it! It took about 20-30 minutes.

I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!

i dd not notice at first and started the self cleaner,,,i notice the self cleaner did not work,the screws had to be sprayed with dw30a couple of times and a pair of pliers to remove screws(no wrench set)after removing screws pulled the wires out to see and removed the connection to wires,,,replaced with new bake element and replaced the screws works fine,,,by the way i am a 64 years old grandmother

Nothing to it. Took off the old ones and put on the new! Tada - new stove!!

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

UNPLUG the oven. Following what every else was doing, I removed the element first, then disconnected the contacts. The leads on the contacts are not overly long, so I found myself removing cover on rear of oven when reconnecting red and yellow wires. Required removing two more screws with nut driver. Should I have to replace another element, I would remove rear cover first, unplug wires from element, remove element. Reverse procedure with new element.
While waiting for new element, be careful when turning on stove top element. Don't turn on oven by mistake, and when you do it, turn it off as fast as you can.
If you use stove top while waiting for part, don't forget to UNPLUG the oven. Won't be but a day or two. Very happy customer.

Removed bolts unplugged unit then plugged new unit in. Put bolts in and unit works great.