JCBP36SK1SS General Electric Range - Instructions

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

had the right parts and the installation was a breeze. Have new burner bowls and stove looks brnad new.

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

The longest part of the job was finding my misplaced nut driver!!Note:A small socket set will do.Unplug stove from outlet,remove rear cover panel,lift stove top up to access terminal. remove the one screw that holds the terminal and slide off the two wire clips that hold the wires up out of the way.next clip off the old terminal leaving the old wires so you can tape the new wires on just to pull them through the hole.Once you have the new wires pulled up to the heat control unplug old and replace with the new,tighten the screw on the new terminal and don't forget to slide on the wire clips

First and foremost I read each of the blogs from your site from other people who have repaired this part. It was great.
First I unplugged the stove. Removed the back plate of the stove by unscrewing 6 screws. Removed the heating element & drip pan. I lifted up the stove top to examine the receptable, and removed the receptable held in place by a single screw using the nutdriver.
Once it was removed, I cut the wires attached to the receptacle with pliers. I screwed on the new receptacle, and taped the new wires to the old ones which led back to the back panel where they were attached to the switch.

By doing so, I was able to easily lead the new wires to the back side of the stove panel. I removed each old terminal wire and replaced it with the new one. (I had read in a previous blog that the polarity of the new wires didn't matter). I replaced the drip pan, and heating element, turned the switch and everything was working just great! I replaced the back panel, and that was it!
As you probably can guess I have never attempted to repair any type of appliance...ever! But your website and the people who shared their stories empowered me to do the job. Thanks so much!

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.

Since we got the stove,this is the second time we've repaired these connectors. The first time the connectors came with pre-stripped wires, wire nuts and heat shrink tubing. This set came with pre-attached spade terminals, so I had to crimp the mate to the wires in the stove then put heat shrink tubing on the splices. I also had to bend the part of the connector that mounts onto the stovetop. These had a horizontal tab for the mounting screw rather than the vertical design that our ranges uses. If the connectors designed for the earlier model were available, it would simplify installation since shrink wrap and wire wraps came in that kit and the mounting bracket would fit correctly.

First I removed the burners and pulled the stove out to get the back cover off. Removed the back cover after main power was shut off. Removed old burner terminal blocks and replaced with new ones. Replaced back cover and pushed stove back into place. Turned on main power to stove checked burners and they worked. DO NOT REPLACE OR DO ANY ELECTRICAL WORK ON ANY MAJOR APPLIANCE WITH OUT FIRST TURNING OFF THE MAIN POWER SOURCE.

Received complete burner receptacle. Decided to take off stove back to plug in directly to burner control.
Turn on stove on low. No heat. Bad coil element. Checked for power at coil element. Switched another burner. It heated immediaetly. Have to order or find a burner element

Thank goodness for PartSelect.com
When we moved into our home the microwave and electric range are obsolete appliances and were missing parts. PartSelect.com has pictures of parts on one inch grid pattern so I was able to select the hard to find parts that would fit perfectly and they did.

My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

It was easy to just replace the old burner bowls rather than try to clean them. The peices ordered from Parts Select were a perfect match and they arrived on a timely basis.

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!

Took out the old ones and replaced with the new ones. Very simple task. It didn't take 5 minutes.