JE1360GA01 General Electric Microwave - Instructions

After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.

The oven overheated when timed cooked was pushed with an empty oven instead of the timer. The oven outside was very warm. I thought the oven was toast and we searched for a comparable one but found they all were rated average to lower than average. So I took the oven cover off aafter buying a special screwdriver bit at ACE Hardware for the security screws. I saw no burned or melted parts. Under the cover was a schematic in an envelope. I traced the hot wire through the fuse and checked the fuse. It was good. Then I traced the neutral wire to a "Flame Sensor" and I wondered what that was. I discovered online that this is an oven over-temperature sensor. I tested the part and it measured infinite ohms. Eureka! I ordered the part and broken light bulb which came promptly. Both parts just require push-on wire connectors and small metal tabs which are bent 90° to hold the parts in place. Very quick and easy repair.

PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Unit was painted inside recently, but apparently some paint fumes still lingered so that when the unit was turn on, there was a very small explosion that took out the flam sensor thermostat. This thermostat interrupts the white leg of the AC input and cuts off all power.Performing a continuity test on the flame sensor showed it was permanently open (no continuity). Turns out I had a similar part from an old coffee maker and when I installed this part, the microwave turned on just fine. So I order the correct sensor from Parts Select. Part installation involved removing the TT20 Security Star bits (4) and the right/left side phillips screws. Now the top/side unit cover comes off by pulling the cover backwards and up and out. The flame sensor is in the middle of the front section underneath the top cover, and comes out easily with pull-off connectors. There are also bendable pins that hold the sensor down flush to the top of the unit.

Just like the directions said. Very simple.

I have the built-in microwave in the cabinet. The hard part was getting it out of the cabinet. Once out, removing the cover and replacing the bulb and fuse was very easy. You need the tamper proof star bits to take out the screws holding the cover to the microwave. I got the bit set from Amazon for about $8. My fuse was OK. But I replaced it anyway, since it was 4-year-old. I am no expert in appliance repair, but found it fairly easy to do the repair. After unplugging the microwave, wait for 20 to 30 minutes before opening it, so that the capacitor inside completely discharges. It is supposed to discharge in 30 seconds, but why take a chance of electrocution..?

Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.