JEC9530ADB Jenn-Air Cooktop - Instructions

Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

Ordered new knobs & now all burners work. Easy installation.

My grandson, age 15 did the replacement. Now, how easy is that!

After unit dried I turned top back on and everything worked but right front control and no fan. I disconnected power, removed BX whip at junction box, took top out, flipped over and removed screws around side , lifted up about 4" disconnected fan laid cover back over BX. looked at right front control and saw circuit board and black all around switch area got numbers put together and ordered part. I talked to about 5 other places and didn't have a clue or part was not available. The woman I talked to knew her stuff and asked all the right questions because there was no part names or list other than right front control.

Simply replaced old switch with new one. Was very easy to do.

Important to unplug the appliance first. There were two screws which were at the top opening of the oven. They were a bit obscure, but with a bit a searching, I was able to find them. After removing those two screws, the entire top lifted up. There were four screws from the bottom of that assembly which were easy to find, and once removed, the top lifted of easily. I found it easier to remove the two power lines with two easy disconnects, this made it easier to work on the assembly. The element itself was held down by two simple clamps which required no tools. There were four easy to remove wires, and the element came right off. Simply reversing the process put it right back together, plug it in, and back to cooking again.

Our cooktop is about 9 years old. Great appliance, but poor engineering/design choice to have aluminum knobs with plastic knob shafts, that almost every time the burner gets turned on, the plastic shaft gets stressed and they crack, rendering them useless over time. I replaced all five (5), for about $80 delivered, since I got tired of repairing them. I did see a very helpful post from a guy in Arizona (thanks if you're reading this) whose daughter glued the shafts inside and out, and then wrapped them in wire. I did the same thing with my spares (I have about 7 now, after replacing one or two over the years), as I took the metal sleeve out of the middle, glued them inside and out, and used small plastic wire ties to close them up tight, then putting the metal insert back inside. After the glue dried, I snipped off the end of the wire tie. It worked great! Thanks, Tom D., from outside Boston, MA.

I took the old knob off, got needle nose pliers to get the small steel sleeve off the post, and put the new knob on. The knob had a number on the underside, but it is not the part number. Part Select's picture showed the number, so I knew it was the right part.

I actually did it manually. It was fast and easy.

Only hitch I experienced was identifying the correct replacement. The original diagram presented the accurate shape of the element my range required. However a different shaped element was displayed when I noted my unit is a series 12 serial number. I ordered it (with reservations) and as it turned out the replacement was identical to mine. Next time I will have a lil more confidence in the instructions given.

Turned off circuit breaker.Removed cooktop from counter top. Used small knife to break silicon seal. Removed glass top from pan by removing retaining screws.The removal of the old part required removal of a nut on the switch shaft which was not obvious . This required the needle nose . Otherwise the replacement was simply exchangeing the wires.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

Simple repair to replace stripped out knob. More importantly we ordered the part over Christmas and it arrived within 2 or 3 days

Unplugged the power cord first. Opened oven door and removed the two screws that held the stove top glass down. Lifted the glass top and removed the four wires connected to the element. I taped the wires to the lid in the pattern they were attached to the element. remove the element from the brackets. The new element was an exact match. reversed the sequence. Put a pot of water on and boiled a hot dog! Perfect! Great part and speedy delivery!!

The hardest part was finding the part number...and that wasn't all that bad. Perfect match; perfect fit.