EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Keep typing for more specific results...
Models > JES1460DS2WW > Instructions

JES1460DS2WW General Electric Microwave - Instructions

All Instructions for the JES1460DS2WW
61 - 75 of 93
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The problem I had with the Microwave Oven was noise when Plate was rotating
After contacting GE support I realized the only interest they had in helping me was to recommend sending a $$$ technican to diagnose the problem. I decided to go to the Sears Parts select website.to see if others were experiencing the noise me microwave was making. After reading through others posting on the subject I decided to purchase the Synchronous Motor. While waiting for the part to come I decided to lubricate the hub of the spides that rotates the plate with white Lithium grease. After a couple of times utilizing the microwave noise went away so whn the part arrived at me home I put it in a drawer just incase I need it a some future date. Hope that someone else finds this information useful. "The Crafty Dodger in Houston"
Parts Used:
Synchronous Motor
  • Kenneth from Richmond, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All power to the microwave went out.
PartSelect had helpful repair instructions on-line which made the repair easier and faster. Unfortunately, there were other problems with the oven that immediately blew the new fuse I had just installed. It was then determined that additional repair would most likely cost almost as much as a new microwave.
Parts Used:
Microwave Fuse
  • Michael from East China Township, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
microwave just stopped working
First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.
Parts Used:
Microwave Fuse
  • James from Fall Branch, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Parts Used:
Microwave Fuse
  • Stephanie from Kernersville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Powered Off completely
After reading reviews that there was no power what so ever and a fuse replacement will solve the problem, I tried it. Replacing the fuse is very easy (and I am not handy at all). All you have to do is remove the microwave cover from the top by removing two screws, slide the cover to the left and pulling the cover off. Then remove the grill in front of you, by removing one or two screws. The fuse is in front of you, use pliers and be firm but gentle. Replacing the fuse is easy but it did not solve my problem.
Parts Used:
Microwave Fuse
  • Mohammad from Piscataway, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Quit working
Just like the directions said. Very simple.
Parts Used:
Microwave Fuse
  • William from Socorro, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Microwave light went out
I have the built-in microwave in the cabinet. The hard part was getting it out of the cabinet. Once out, removing the cover and replacing the bulb and fuse was very easy. You need the tamper proof star bits to take out the screws holding the cover to the microwave. I got the bit set from Amazon for about $8. My fuse was OK. But I replaced it anyway, since it was 4-year-old. I am no expert in appliance repair, but found it fairly easy to do the repair. After unplugging the microwave, wait for 20 to 30 minutes before opening it, so that the capacitor inside completely discharges. It is supposed to discharge in 30 seconds, but why take a chance of electrocution..?
Parts Used:
Light Bulb - 125V 20W Microwave Fuse
  • Peter from Clovis, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door Interlock Switch Failed
Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.
Parts Used:
Microwave Door Interlock Switch
  • Michael from Littleton, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
microwave would run for a few seconds and die. come back on by itself and die again in few seconds
Upon inspecting the internals found burned thermostat and one lead. Got the parts, replaced and now working fine.
Parts Used:
Microwave Thermostat
  • r ravi from houiston, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
When trying to run, intermittently, the light would come on but the tray wouldn't rotate or cook. When the door was open, the tray would intermittently rotate.
I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.
Parts Used:
Microwave Door Interlock Switch
  • Sam from Chandler, AZ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Turn plate started making clicking noises and eventually stopped turning
It was extremely easy. I put the microwave on my table upside down and could see the motor thru the holes in the bottom cover. It appeared as though the outside skin had to be removed to access the motor but after looking at it there is an access panel I did have to cut it loose. Not bolted on. There was a message stamped into the bottom case next to the panel that said to debur after panel is removed. So I cut it loose on 3 sides was able get to the one screw swap the motor and reinstall it in about 5 minutes. It works like new What an easy and quick repair. Thanks
Parts Used:
Synchronous Motor
  • Henry Lindsey from Slidell, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Microwave would turn on ,BUT turn table would not turn and oven would not heat.
Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Parts Used:
Microwave Door Interlock Switch
  • Earl from New Philidelphia, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JES1460DS2WW
61 - 75 of 93