JGB280DEN2WW General Electric Range - Instructions

slid the old ones out and slid the new ones in. done

When turning on the oven, I could see the ignitor red hot but it would not ignite the burner. I ordered the pair of new ignitor and burner tube. Upon removal of the burner tube, I saw a large hole in the tube where the center of the ignitor is located, clearly in need of replacement. Unlike some other ovens, the connector on the new ignitor was the exact fit for my oven (Hotpoint RGB745BEA7WH). After access to the tube, the replacement took less than 10 minutes not including watching about 3 youtube videos on how to actually do the replacement prior. You should turn the gas and electric off but ooops, I forgot. I was shocked at how easy this was!

With the model number I wnet on Parts select site and located the part through the problem finder selection,(GREATFEATURE!) (74% the problem is the Flat Style Oven Igniter) (watched the video on installation and compared my unit with the one in the video). The video explained installation completely and made it very simple. The only critic is that the oven door can be removed completely to make it easier to get in the the oven, opening part way and lifting up the oven door will come completely off. Also the broiler pan drawer can be taken completely out if you would need to get in this way for some reason. Final note: I called the local GE dealer Parts dept- they would have had to order the part anyway and it would have cost three times what Parts Select charged me.Save $$$ great! .

Removed old gasket, did need to use pliers. However, it was easy. The new gasket just snapped in place ...super easy.

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.

One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !

I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.

Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)

Hired gas company to do repairs for safety reasons

just removed the old burner cap and put on the new one.

1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.

Removed the old glowbar's two screws. Didn't take a mental photo of its proper placcement (or a real one, which would've been smart). Removed screws holding 1) a heat protection plate, and 2) wire harness plate. Installed the new glowbar, hopefully, the right way - with its heat-plate facing the gasline of the over/broiler. Reinstalled the heat protection plate and wire harness plate. Hasn't blown up yet!

Tested for power to the igniter, (had power) so I knew it must have been the igniter that had failed. Removed two screws that held the shield in place, remove two screws that hold the igniter and disconnect the plug form the igniter, replace with new igniter.

I let my brother do the actual installation but it only look about 15 min. I did look at the website of the appliance manufacturer first and then came to this website. The cost of the part I needed was almost half as much as the other site. When I saw that someone with the same oven model number and had the same problem and was able to fix it, I decided to order here. It came quickly and my oven now works.

In general, other repair stories on this site collectively give a good description of the repair process. My words concern the decision that has to be made as to which element is bad - igniter or gas valve. To reach a conclusion about this question, I was comforted by the fact that I could measure the AC electric current through the gas valve which then let me decide that my problem was in the igniter. Since the circuit is a simple series with three elements, thermostat, igniter, and valve and the resistance of the valve unit was 1.0 to 1.2 ohms (per GE range equipment instruction which came with the range) by measuring the AC volts across the valve, I found (by dividing the volts AC across the gas valve (2.3 volts) by the resistance of the valve mechanism (1.0 ohms) that my old igniter was only supplying 2.3 AC amperes (instruction sheet states 2.9 amps. is needed to actuate the valve and further while heating of the oven is occurring the valve AC current will raise to 3.2 to 3.6 amps.). At 2.3 amps. the igniter will glow at a yellow color but will not actuate the valve. When you replace the old igniter with a new one you will enjoy to measure voltage across the gas valve once again and discover that the voltage rises to 2.9 volts and that the gas turns on and the heater tube gas is ignited.