JGS905KEKC General Electric Range - Instructions

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

Watched video

Replaced gas control valve problem solved, all went well

Turn gas off. Remove front door by pulling the lock covers back and pulling door up. Remove all cooking racks. Push back and lift enamel cover plate. Remove heat shield. Either use crosstip screwdriver or nutdriver (ratchet driver works as well, all the ovens have a different size nut/screw so check your size) and remove ignitor. Remove small shield and gas burner tube from pan. Remove all nut/screws from pan, lift up and pull towards front (ignitor can not go through pan) exposing electrical connector behind insulation. Disconnect and pull through pan. Replace pan (I had to replace older pan due to rust) and push connector from new ignitor through hole and connect to plug. Push pan in attach new ignitor (easier) to gas tube burner and place burner back through hole. Reattach shield and burner to tube to pan. At this point I tested the new ignitor which worked perfectly. Turn off oven. Place heat shield over burner tube. Replace enamal cover plate. Replace oven racks. Place door and lock holders on the hinges. Easy. BTW I am 70 and it took me just at 25 minutes with set up for tools, door, rack and enamel cover removal, heat shield removal and then the more labor intensive nut/screw removal, old ignitor and gas burner tube removal, pan removal, new ignitor replacement, new pan replacement, gas tube with shield attachment, heat shield attachment, enamel cover, grill racks and door attachment. Perfect parts fit well work well.

Changing out the burner assembly completely fixed the gas smell issue. The burner was deformed and rusted in the area adjacent to the igniter. The oven burns properly now, and no extra gas smell exists.

Performed repair using a video for reference.

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

recieved part the next day. looked different but I followed instructions and the part worked perfect.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

twisted it in place

The repair is not complete because the two screws that hold the igniter to the oven Burner Assembly tube were frozen in place, probably from the heat over time: One stripped and the other broke, necessitating the removal and purchase of the oven burner tube and screws.

replaced lights in refrigirator and freezer

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.