JK25*R3 General Electric Range - Instructions

Before ordering the new part, made sure the problem was the burner and not the wiring in this very old stove by putting an ohmmeter on the terminals of the burner after removing it. Since it showed no conductivity, the burner was bad (could have put the voltmeter on the wires and turned on the power to ensure power was coming in......but did not want to mess with 240 volt/high amperage. With power off at the breaker, installed new burner. One caution... since the wire on the burner terminals is pretty soft, don't bend them by putting too much torque on the screws. This turned out to be my only problem.....I had to clean up the screws and work them through the copper terminals with the burner outside the oven before attempting to screw them on the wire connectors in the oven. Not a big problem, but if you bend the terminals too much when you install the burner in the oven, you run the risk of shorting them together, or breaking one. And that would be a big problem.

I removed the two screws that held the element panel on. I removed the lead wires from the element, making sure the wires didn't retract back into the wall. I put the new element in, reconnected the lead wires and put the screws back in. I was concerned that the panel wasn't as long (top to bottom) as the previous one and it barely covered the hole, but it works fine. It would have cost me $60 to have it done by my home warranty company so I saved almost half.

First I removed the two screws that hold the element in place. I pulled the element out and disconnected the two wires that hold it in place. I reversed the process for the new element and viola! The oven works just great. The element actually arrived a day earlier than expected. Thanks Parts Select!

My husband helped me pull the range out from the wall to unplug it, I removed the screws on the hinged bracket, pulled the wiring out a couple of inches and removed the screws attaching the element to the wiring. Then I reversed the process. Easy as pie. The most time consuming part was unplugging the range, but as it is 220v (can kill you) I consider it a nesessary step. The best part was the price and availability. I ordered the part on Sunday p.m. and got it on Tuesday p.m. at half the price quoted by a national chain.

Used a nut driver to remove two hex screws holding element to the back of the oven and then the two hex screws connecting the element to the oven wires. I pulled the element out and reversed the process. I turned the oven on and made sure the element worked.

I used a philip screw driver to remove two screws which enable me to pull the wires out about three inches from the back of the oven and replaced it with the new one after disconnecting the wires from the grill. The hardest thing was the limited space.

Turned off circuit breaker, took two screws out to be able to pull element out from back. Took two more screws out to remove old element from oven. Did the opposite to install the new bake element. Turned power back on, and it worked fine.

Turned off breaker,first . Then removed 2 nutscrews and pulled unit out , 4 inches ,removed 2 nutscrews joining the 2 wires and the 2 terminals of the bottom element. Removed bottom unit and replaced with new unit . reversing the process. Turned breaker on and tested the oven. Works fine. Took less than 15 minutes.

The hardest part of this entire repair was locating the right socket and explaining why/how I burned my fingers (yes I had to touch the element to prove to myself it was that easy to fix and worked). 4 screws, 1 replacement part 5 minutes no cussing. This was the easiest repair I have ever done.

remove 2 screws holding element to oven back wall/ unscrew wires from element/ new element install the reverse of removal

Removed screws that hold element in place. Disconnected the two electrical leads. Put the new element in place, hooked up the two leads and installed the the screws that hold the element in place.

Because of the age of the oven it took a little time to loosen the screws that held the element in. Once the screws were removed it was a matter of pulling the element out about 3 inches and disconnected the two wires, then it was a matter of repeating the steps in reverse. Very quick and easy

First, I shut off the power to the oven... no point in risking a nice electric shock. The next thing I realized was I could not see anything... enter the flashlight. Then, well then it was really easy. I removed the two screws that held the element to the back wall of the oven, pulled the element (and some of the insulation stuffing) out about 2 inches to reveal the two wires and their connecting screws. Unscrewed them, put the new element in, reconnected the wiring, restuffed the stuffing and reattached it to the oven wall. Turned on the power and she heated up faster than ever. Speaking of fast, my part arrived the day after I ordered it and that was with regular shipping. Thanks fellas.

First I shut off the range breaker in the main electrical panel. I slid the oven door off for easy access to the back of the oven. I loosened the two hex head screws holding the element to the oven wall. I pulled the element forward to reveal the two hex head screws holding the wires to the element and removed the old element. I attached the wires to the new element with the hex head screws, fastened the element to the oven wall, slid the oven door back on, and flipped on the breaker. I gathered up my tools and left the apartment. It took me longer to get to the apartment and back than it did to do the repair. PartSelect.com got the part to me within two days of my order, and for six dollars in shipping that's great.. PartSelect.com has been added to my internet bookmark.

This was quite an easy fix once I got the correct part. It was my own fault for ordering what I thought went with my oven. I didn't expect to be able to even find a new heating element because the stove is almost 40 years old. Except for that one part it works just fine. It took me about 20 minutes to do the repair. I unplugged the stove, unscrewed the 2 screws holding the element to the back of the stove, pulled it out far enough to unscrew the 2 screws attached to the wires, screwed the new part to the wires, screwed the whole unit back onto the back of the stove and plugged it back in. It works great. Moving the stove away from the wall was more difficult than installing the new part. It couldn't have been easier and it was a lot less expensive than buying a new stove. Also, the customer service people I spoke to were very friendly and helpful and there was no problem returning the incorrect part. I would recommend this company to anyone who asks.