JVM1533BD004 General Electric Microwave - Instructions

Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.

The repair went well. It was really easy to replace the filters. We bought this house recently only to find out the previous owners threw all the filters for the microwave out including the two reusable grease filters. The grease filters were easy, just slipped them in. The charcoal filter required taking the top plastic vent off by removing two screws and slipping the filter in.

Looked on line and found a you tube that said to check the door micro switches (there are three of them. Found one of the switches had an actuator that was stuck down. I got the actuator working but problem was still present. Another you tube showed how to repair the contacts in the switch and that solved the problem. however the plastic piece that holds the switches was broken and would not hold the switches securely. Ordered that piece and a new switch. Remove the vent plate on top (one phillips) and the control panel (one phillips). The switch holder is held in place with 2 phillips and is a little tricky to get it out and undo the wires. Once out, it's just a matter of putting the switches into the new holder and reinstalling it. Google the model number and the problem and there's virtually a you tube to repair ANYTHING.

Disassembled the front cover, found slow blow fuses, then replaced with microwave fuses 250V-20Amp. Utilized a few fuses to pin point the problem, Microwave functions all worked except the express feature, made an assumption after using a tester that it was the high voltage capacitor and the diode that attaches. Replaced both, plugged in and tested. Worked! reinstalled the unit. Sucessfull for the past month.

Moved the stove from underneath the microwave. Took the microwave down and turned it over. this need not be done. took the screws out to remove the bottom panel. there is a quick disconnect that need to be opened up. used pliers to remove the bad sockets and installed new one, used pliers to seat them. put bottom panel on, hooked up the quick connect. put the screws in and tightened them. installed bulbs and hooked up the electric and turned the lights on, they worked. installed the microwave, slid the stove back in place.

Unscrewed the vent at top of microwave exposing small access to bulb. The access to this was very limited so that was the major issue in changing the bulb. You needed small hands to do the job.

Check with Digital meter all connections.Find a Thermostat open loop.This thermostat is near the Megatron .

The tray came within 5 days and I simply took it out of its well-packaged box and slipped it into my microwave. It is working just like new. I can't thank you all for being so punctual and reliable. better than having to buy a brand new microwave.

I just matched the prong in the turntable hole and coupler fit into the hole perfectly. All The Best.

The burned remnant of the coupler was a bit difficult to remove. I did so with a pliers and also used the pliers to clear out some burned fragments of the coupler. With a flashlight I determined that the slot for the coupler was now clear. I matched the configuration of the slot with that of the new coupler and it slid immediately into place with no difficulty whatever.

Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.

I had already removed the old grease filters. Unwrapped the new grease filters and popped into place. No tools were necessary.

Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of the freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door

Another company said the new plate would arrive in mid-March, this company seemed to be faster so ordered the tray here, and it came in less than a week. I put the turn button back in the center hole, set the wheeled ring on the bottom of the oven, fitted the new glass tray onto the turn button.

Placed the new tray into the oven.