KDTE304DWH0 KitchenAid Dishwasher - Instructions

Pulled off old seal. Pressed into groove the new door seal. No parts required.

thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.

Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.

I followed the video on the site and it worked perfectly!

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

Pulled dishwasher out from under the counter, removed faulty seal, installed new seal. Easy to understand directions are on web site.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

I basically used the instructions provided with the "Your Order Has Shipped: email from you. It was quite easy. Thank You!.

Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!

Thought this would be much easier than it actually was. Long story short, ended up calling is an appliance professional to install the part.

The rinse aid cap fixed the problem of leaking rinse aid sta9n9ng the dishwasher every time. What an easy and cheap fix.

All four original wheel assembly's were difficult to pop out so used pliers and cutter to brake original part and remove it. Nothing on the original wheel assembly was needed for the repair so braking them off was ok. The new wheel assembly parts, with two wheels on each (4 total), two wheel assembly's on each side of the rack, were easy to install- no tools needed. Each wheel assembly just popped right into place.

Popped damaged/worn wheel assembly off, snapped new ones in. Easy peasy

Pull the old seal out and push the new seal in. Done. Easy. The only issue is the door is still leaking and I have to replace the seal and the plate that goes across the bottom of the door.

Order both this seal and the seal for the bottom of the door at the same time.