KERS303BSS0 KitchenAid Range - Instructions

Turn off the power to the stove, either by tripping the circuit breaker or unplugging the stove. Open the oven door. Unscrew 4 screws on the inside top of the oven releasing the cooktop.
Lift the front of the cooktop and release it from the retaining brackets on the back of the oven. The element will be exposed. Disconnect the wires remembering the locations. It is pretty simple because the wires are in a harness. There are three clips holding the element in place. With needle nose pliers, disconnect the clips from the surface. Remove the element. The retaining clips are in holes in the back of the element. The holes are numbered. Remember which number holes are being populated with a clip. Remove the clip from the old element and place it on the new element in the same hole #. Place the new element into the vacated space on the cooktop place the three clips in their respective places which will align the wires. Hook up the wires to the new element. Replace the cooktop (I cleaned it first) and screw it back into place. Turn the power back on and you should be good to go.

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

Watched video & did just guy in video did. Very easy job & the burner works like new.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

pulled stove away from wall. took back cover off by removing 10 screws. Identified switch number and ordered replacement switch. pulled knob off front and removed 2 screws from switch and pulled switch out. swapped switch wires and reinstalled switch, back cover and slid stove back into place. Very easy, the whole process took about 1/2 hour.

Unplug range, remove cover from back of range disconnect red wires from element spade connectors. Remove oven racks, remove two screws from back of bottom tray, and remove tray. Remove screw from element bracket and remove element. Install new element and repeat steps in reverse order. Done.

An easy repair. I just needed a screwdriver.
I watched the video that you sent me with the part. I followed the directions in the video and the job was completed in 30 minutes!
Easy Peazy!! I’m back to cooking!

Followed a video I found online showing how to replace the bottom bake element. It was very easy to do. I simply unplugged the over, removed the back wire cover and detached the damaged element connectors.

I then removed the bottom oven cover which conceals the element. Unscrewed and removed the damaged element and replaced it with the new one. Connected the wires to the new element and then Installed the bottom cover along with the back wire cover and plugged the oven back in. It was really this easy.

Watch the video...

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

very expensive to buy the part but just tighten the screw intot eh predefined place.

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.