KRSF505EBL01 Whirlpool Refrigerator - Instructions

This is an easy fix. The hardest part was just determining which part to replace. But the Q&A's for the ice maker from this site steered me right. And their video on how to install was easy to follow. The only difference I found was my Whirlpool had only 2 electrical connectors instead of the 3 in the video. I finished the job in about 15 minutes so everything in my freezer stayed solidly frozen.

After removing shelving and evaporator coil cover, suspended water bladder and evaporator coil with bungy cords. Removed and repaired drain pan, closing pitted holes and applying a coat of paint. Pushed evaporator fan WITH strofoam replacement to better insulate coil. Ensure that fan is facing up so that evap coil cold air is pushed up to top shelf area (mine came facing down). I used two digital thermometers, placing one on the top shelf and the other one the middle shelf to measure temp. Both read 37 degrees, which is fine.

Never did this particular repair before. Fairly easy.

This is regarding the top light in the freezer, Small screwdriver inserted into tabs on the right side of light pops it right out. Unplug and remove light. Plug in new light, snap into place DONE. Be sure to remove plastic film

First turn off the ice maker. Then there's four screws in the very back you remove pull out the cover. There's hex head 516 bolts maybe quarter inch that hold in the ice maker unplug the ice maker reverse process

1. Removed 2 screws on top hing.
2. Easily lifted door and place on table.
3. Removed set screw for door cam.
4. Removed stop bracket.
5. Reversed steps 4 thru 1.

When tightening top 2 screws, make sure door gap is consistent and top of frig door aligns with the top of the freezer door.

NOTE: The lady at PartSelect who helped me with my order was great. Took the time to verify my parts. Prior to this I had bought the part from a nearby appliance parts store. They sold me the wrong part, even though I showed them a picture of my model number plate b4 ordering. In the future, I will always go to PartSelect for my appliance part purchases.

Unhooked water line from house to fridge then unbolted valve from fridge body then removed plastic water line from fridge to valve by pushing in on pex release tab then reversed process with new valve. Works like a charm. No more leakage. Wood floor is dry and Happy!

The repair went great, however, I had someone to put the part in for me.

Simple to replace. 6 screws out. Unplug connections... Plug back in, replace screws.

Unfortunately still not making ice. Will try fill valve replacement.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

Took lower back board off, took part off to expose it so I could see where it was leaking, got part number, ordered it.
Shut off water to frig at wall shut off, unhooked both hoses and plug, hooked new part up, turned water back on. Watched couple days to make sure it wasn't leaking. Vacuumed out back good, which I was amazed didn't really need it, hooked part back in place, replaced back with screws.

Remove the top two drawers, with a small screwdriver pop out module, unplug, plug in new module, press back into place, put drawers back, DONE! 5 minutes easy peasy ??