KUDE60FVBL1 KitchenAid Dishwasher - Instructions

very easy, thank you for your quick service

simple...a female did it!! Dealing with PartSelect was so easy...your was the only web site that made it super easy to find my part. Placed order and paid for it...part arrived the next day!! Sent web site link to hubby too. When we need parts again for any applicance in our home, we will check your site out first!!

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

replaced

Other than the repair part being at the bottom of the dishwasher and you had to lie on your stomach to do the swap out, it was just one screw, move the part out a little closer to you then pull off one electrical wire, and pull off one small hose and using wrench unhook the other small hose.

Of course I had to take it apart a second time because of a leak, but using 3 or 4 circles of the white plumbers tape, it took care of the leak.

Rolled out old, rolled in new.

Removed new from box and installed rollers as instructed that's all there was , very easy.

The new lower spray arm fit right into place. All set, and I will always check to see if it is sitting properly!

I followed the video directions on line...they were exactly to the point to do the repair.

i asked the vrtual repair stating the problem of my dishwasher machine ,he then give me two possible solution change the water presure switch which i did order the part and installed it and it works now..............thanks partselect.

You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.

Removed old rack and and removed old rollers and installed old rollers on new rack as they work better than the new rollers sent with new rack

Disconnected Power, Turned off water valve, disconnected drain return line, disconnected water line, removed two screws on inside-top that was mounted to counter, pulled out dishwasher while feeding power cord, drain line, water line. Turned Dishwasher on it's side and disconnected water line and water fill line from Fill valve Assembly. Disconnected power connector from Valve. Removed one screw from Fill valve assembly and removed Fill valve assembly.
Installed Fill valve assembly and screwed screw back in. Installed Water line and water fill line from valve. Snapped power connector back in. Doubled checked Fill Valve connections to make sure they were tight. Slide Dishwasher back in while lines and power back through to under sink. Made sure Dishwasher was set in place and mounted two screws to counter. Connected water line to water valve and connected discharge line back to it's location. Turn water back on. Plug power back in.
Turned unit on and checked for leaks at the fill Valve assembly, water line and discharge tube.
Saved ~ $ 100.00. Easy job. I wished I didn't wait so long when it was making the noise for so long...Good luck..

Since I had manual from initial installation I knew code meant heater was malfunctioning. Went to Sears, Lowes..no parts to repair. Instructed to go to appliance repair shop, closed of course...ordered online instead here and received in 2 days. Repair took 20 minutes. Super easy! Do not attempt to use adjustable wrench to tighten, use socket set as plastic electrode casings will be compromised. Takes some tork. Probably saved $100-$150 repair call. Wife was pleased. I was suprised how easy.

Grabbed old seal and removed it.(notice how seal was situated in slot)

Pushed new seal in slot that held old seal. close door.

If dishwasher still leaks you put the seal in backward (I did!)remove seal reverse it and reinsert it.