LDF6810BB-02 LG Dishwasher - Instructions

Removed two screws (one each side) and the toe kick plate at the bottom. Slide the dishwasher out from the cabinets about 10", remove broken cord clip from door and spring. Install door clip and wrap cord around pulley , attach to spring then attach spring to door, lifting the door will help attach the spring. Do one side of the door at a time.

I watched the video and it showed every step to remove the old part and replace the new one. Went fairly easy except when put the new motor in the new seal was difficult to put on. I think if I would taken off the front door I could have got close to the back of the rubber seal to secure it a little easier. Had to use a rubber hammer hold my breath to not brake the plastic motor. But that was only way I could get in. The video showed it going rely easy that was not the case because it was a new seal. In the end it all worked out.
Thanks for the video's to help

connector was broken. just attached new connector to spring on each side of door. easy fix.

The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.

I would just like to return these rollers and would like a return address.

Thank you!
Penelope

Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Installed new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.

I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.

Was not able to see where the Stopper, Rollers ( Part # PS3523062) could be attached to the back of the bottom tray, to fix the problem. So the parts were useless.

These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.

I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.

Replace basket with new replacement. Ordering and shipment VERY EASY! I have used your service in the past and will continue to in the future. Shipments are fast and accurate.

Remove line to top wash area. Then removed all screws and rubber seal . Then just back step. In about 30 mins. it was ready to run ,

Uninstall dishwasher screws. Lay dishwasher on its side. Remove bottom plate. Remove old drain line. install new line. Test for leak. The trick was figuring out that I could only access the line through the bottom of the dishwasher.

Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old noise filter from dishwasher frame without removing the whole unit from cabinet and turning upside down.One screw holds the part in the frame. With power off, I used a very small ratchet with phillips screw driver. Pried unit out with screw driver on side to the panel front. It has a retaining tab there.Installation was the reverse. Instead of putting screw back the way it was originally installed, I screwed it in from the outside of the frame. Much easier and just as solid. Tested unit with power on. Hooked up water line. Works great. Note: LG dishwahers have a high repair rate and that this part has a high failure rate. This LG unit was two years old. Never had to fix my 15 year old Sears dishwasher. It still works to this day. (I gave it to my daughter.)

First, PartSelect is great!; fast,& accurate. 1. Inside the dishwasher: remove trays. Remove (A050) lower water sprayer from bottom by pulling up. Remove (F191) top sprayer assembly by pulling away from clip holders. Remove (M110) by removing the holding screws. This part cover the whole sump and has kind-of an open screen circling the unit. Now you will see the white plastic impeller (M120) which is attached the the motor with one Phillips head screw. WARNING. The Phillips head screw (holding the impeller in place) is a REVERSE THREADED SCREW. Turn the screw CLOCKWISE to remove it. Then remove the impeller from the motor shaft. Underneath and outside the washer: Remove the bottom plate. Finally remove the motor by unscrewing the four holding screws and electrical wiring.