Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft w...
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. Th...
This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place...
This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses ...
This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these belts has worn or stret...
This lint filter is a genuine OEM replacement filter for your dryer. Replacing it is easy as it just slides in like your normal filter. Make sure to check the filter slot for excess buildup of lint, a...
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold indivi...
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Hope
January 4, 2020
What is the depth dimension? Looking to replace the washer and dryer and i need to know if the larger newer ones will fit
For model number LSE7804ACE
Hello Hope, thank you for your question. The measurements are as follows. Width: 27 1/2", Height: 73" and Depth: 27 1/2". I hope this helps!
11 people found this helpful.
Was this helpful?
Thank you for voting!
Louise
November 3, 2022
What are the capacities, (load sizes) for the washer and dryer?
For model number LSE7804ACE
Hi Louise,
Thank you for your question. The capacity of the washer is 2.5 cubic feet. The capacity of the dryer is 4.7 cubic feet. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Maria
August 21, 2023
My washer fills with water but won’t spin. I’ve had two different technicians look at it. One said it is the lid and the other said it is the transmission. Is this problem fixable! Thank you
For model number LSE7804ACE
Hi Maria, thank you for writing in. Our research has found that when the washer will not spin the likely cause is the belt's, part number PS2005284. We have attached a video to assist you with your repair. We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Patty
September 20, 2023
What are the measurements
For model number LSE7804ACE
Hello Patty, thank you for reaching out. The dimensions of your model are:
Height: 73 inches, Width: 27.5 inches, Depth: 27.5 inches.
We hope this information helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Harv
March 30, 2023
How do remove an agitator
For model number LSE7804ACE
Hi Harv, thank you for reaching out. These are some general instructions that may help you to do the procedures: To remove the agitator, open the washer's main top with a putty knife. Secure the lid lock by disconnecting it. Then fully remove the main top. Remove the agitator cup. Remove the screw inside the agitator and pull the agitator upward. Your agitator is removed. We hope this information helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel. I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools
... Read moreand about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through
... Read more. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.
