MED7020RU0 Whirlpool Dryer - Instructions

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.

I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.

Glass door was broken with part still in door.
-put tape on glass so it would not fall on me as I dissembled door.
-removed and disassembled door by removing all screws/ torx.
-used shop vac to get most of the shards out then flushed with water for the rest.
-used shop vac to dry door.
-put back together. remember to put big bulge of glass down. the rounded part of the door is the bottom. do not over tighten as the screws go into plastic.
-all skill levels can do this job. it will only go together one way. the glass has a notch bulge that alines with the bracket. worst case is you have to put it together 3 times before you get it right. the door is reversible so it can open either to the right or the left giving you four combinations on how to install the glass. don't over tighten the phillips as they go into plastic. Go for it.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Unplug dryer from 220VAC outlet

Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.

Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together. You may need a small flat blade screwdriver to seperate connector.

Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.

Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.

Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.

Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.

Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.

At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.

Install new tensioner, tighten slightly, then put springs back on.

Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.

This dryer was quieter than its owners remembered it being back when new 15 years ago.

Well worth saving the $ doing your own work.

Good luck on your repair endeavor!

Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pulley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.

Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.

Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.

Ezee pezee lemon squeezee.

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

Followed instructions for standard blower wheel replacement and repair kit installation, which were straight forward. The only real issue I ran into was removing the blower wheel, The instructions say to turn it clockwise and remove it, however this wheel had been on there for a long time and it also has a taper shoulder so it was not coming off without a fight which is why the dremel tool is listed. I had to cut the old bower wheel out in pieces so I could remove the electric motor, which was easy. Once out and on the bench and only the metal hub left on the shaft a 7/16" wrench and large vise-grips got it to break loose. The good side of this is it allowed me to blow out any lint that had built up on the motor, like new again.

Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel