MGR8700DH0 Maytag Range - Instructions

I first shut off gas to stove and unplugged the stove. I then opened the oven door and used a phillips screw driver to remove the three screws under the cover plate that sits behind the gas control knobs . I then removed the cover plate. I then took off the grates on stove top and proceeded to remove the two screws on each burner head with a phililps screwdriver. Some where tight so I used a drill driver on low speed to turn the screws out. After removing the burner heads I had to remove two screws on each corner in the front under the cook top of the stove to remove the cook top off the stove. But before that I had to release the two wires from a clip under the cook top for the ignitor switches before I could lift the cook top off the stove. These should be on the right hand side. Now I had access to remove the burner valve that had the broken stem that the knob is attached too. For this I used adjustable wrench to remove the nut for the gas tube that goes from the burner head to the control valve. Then I had to release the ignitor switch by pulling it off the control valve stem or gently pry it off with a flat head screw driver. Then used 1/4 in socket wrench to remove the top bolt to release the old burner valve off the gas plenum where all the burner valves are attached too. Then pull the old control valve off from underneath the gas plenum. Then i put in the new burner valve making sure it had a rubber seal around it where it goes up through the hole underneath the gas plenum. Then while holding control valve in place put the screw back in the top of the gas plenum through the other hole on top of the gas plenum and screw it in the burner valve making sure it also has a seal under the bottom of head of the bolt that you are screwing in to the control valve. This is so that no gas can leak from the plenum where the control valve is attached to. The control valve threads should be lined up with the bolt since both holes on the bottom and top of the gas rail (plenum) are lined up Use a 1/4 in socket to tighten down the bolt with the seal but don't over tighten. Then reattach the tube that goes from the burner head to the control valve with adjustable wrench and make sure not to over tighten. Then grab the stove cook top that you took off and replace it back on top of stove.After in place make sure to put those two wires back into clip that is under the cook top so wires are not touching the oven. You have to put part of your arm under the cook top and use your hand to try to push the wires back into the clip that's under the stove top. These wires will be on the right hand side. This is kinds tricky to do. Then tighten cook top back down with two screws and reattach the ignitor switch back through the valve stem of new control valve . It should clip in around the valve stem. Then reattach the cover plate over the valves stems with the remaining three screws and attach the control knobs.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Pop old one out and new one in

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

very easy

Screwed in light bulb and glass protector

Took off the screws on the back of the stove and took out the sensor, and put in the new one.