Back
Back
Keep typing for more specific results...
Models > MLE22PRAYW0 > Instructions

MLE22PRAYW0 Maytag Washer Dryer Combo - Instructions

All Instructions for the MLE22PRAYW0
31 - 45 of 747
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Dryer Would Not Turn On
The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about two days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.
Parts Used:
Dryer Thermal Fuse
  • Ribhe from Wildwood, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
19 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy sound from dryer
Just like video except there were two screws in back to take control head off. Be prepared to have shop vacation ready. Clean dryer duct too. Have bandaids ready. Plastic triangles are not easy to take off, video makes it look easy.
Parts Used:
Dryer Repair Kit
  • john from OLYMPIA, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
20 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was making a screaching noise while turning
Repaired the 4 drum support rollers, 1 idler assembly, 9 tri rings, and 1 washer that came with the kit, however, the multi rib dryer belt that came with the kit did not fit my dryer. After several attempts to troubleshoot the problem, I realized that the belt was too small. I contacted PartSelect customer service and advised that the multi rib dryer belt that came with the kit was too small and I need to purchase a belt (P/N WP8547157) that fits my dryer. Adam was very courteous and helpful and very apologetic for the belt not being the right one. PartSelect refunded my purchase for the Parts Kit and I purchased the correct multi rib dryer belt. I received the new belt expeditiously and was able to finalize the repairs. Thank you PartSelect for your support and cooperation. Recommend: Advise customers that the belt in the kit may not fit the recommended dryer.
Parts Used:
Dryer Repair Kit
  • jose from FALLBROOK, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
18 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I purchased the machine from a Scratch and Dent Place
The water pump housing was leaking due to some pre-existing damage and leaking on the floor. The repairman wanted 60.00 just to show up. I purchased a replacement pump from PartsSelect.com and installed it myself by taking off the bottom front panel (two screws on the bottom and unclamping the two hoses from the pump and the two screws holding the pump to the frame and then unsnapping the wiring coupler from the old pump. I pulled the old pump out through the front of the machine. I then installed the new pump and replaced the front cover. I saved myself a lot of money and everything went smoothly! The machine works great.
Parts Used:
Washer Drain Pump
  • rick from ironton, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
20 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy Dryer
I ordered the dryer repair kit and to my surprise it arrived 4 days early. I followed the video instructions on the parts select website to replace 4 rollers, belt and belt pulley. A 1/4 in nut driver attached to my Dewalt drill made life ALOT easier!! My recommendation, when you remove the rollers, take a rag and really clean up the shaft they ride on. Then apply a lightweight spray oil to the shafts. When you install the new rollers they will spin free and easy. Having the dryer apart is also a great time to break out the dust buster of vacuum. Spin the fan motor up front by hand and use vacuum to remove lint or belt shaving from inside the cabinet. Add this step as good fire prevention measure.
Parts Used:
Dryer Repair Kit
  • Patrick from SCHENECTADY, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
17 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
draining problem
Open the bottom screws (hex-screw driver. remove riongs with pliers. use pan to remove excess water remained in pipes. pull to the right and remove. easier than it seems,
Parts Used:
Washer Drain Pump
  • Dr. Merdad from Los Angeles, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set
18 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The felt strip on the filter had come undone.
Took the old filter out and inserted the new one- works great!!
Parts Used:
Dryer Lint Filter
  • Rebecca from Laredo, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
21 of 31 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Catch was broken
I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.
Parts Used:
Dryer Door Catch Kit
  • Inocencio from Edinburg, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
16 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Flashing E1 code for a bad thermistor
I replaced the thermistor earlier, but the code was still flashing. I noticed the heater terminals were charred and pretty well covered in carbon. So, I replaced the heater, the thermostat and thermal fuse and replaced the 3/8" spade terminals on the heater wires. (These are hard to find - most electrical spades terminals are .250. Also, I crimped and soldered these for a connection with the lowest resistance possible). After all that, the code still flashed! I let the explatives fly, calmed down, and ran the control board test. (This is done by pressing "more time" "less time" "more time" "less time" in succession.) The control board was passing all the tests, but the thermistor test, and the only thing is in this circuit is the thermistor, the wires, the connector to the control board, and some circuit on the control board that involves a few resistors and the "brain" chip. So, I checked the terminals at the thermistor, the wires up to the control board and the connector at the board. The control board connector was fairly dust encrusted, so I unplugged it, cleaned the control board terminals and sucked away all the lint and dust. Finally, I carefully removed earch crimp terminal from the Molex connector (the white female connector) and cleaned and bent them to yield a better connection to the terminals on the control board. I put it all back together, and thus far it is working fine.
Parts Used:
Dryer High Limit Thermostat And Thermal Cutoff Kit
  • John from Cedar Rapids, IA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
19 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Locking the drum for moving
Remove the plastic caps from the rear of the machine. Insert the locking bolts into the slots. There is a clip on the bolts with a corresponding hole in the outside edge of the slots, this tells you exactly where to place the bolt. In my case i used a large flat head screw driver to move the drum into alignment with the bolt by inserting the driver into a different slot and prying the drum into place. When i had the first bolt started and about hald way in, i did the diagonly opposite bolt, got that one about half way in then did th elast two. i did not need to pry much on these two as the drum was no lined up fairly well with the bolts. I tightened them up and moved the washer. You do NOT need to call a maytag agent to come out and do this.
Parts Used:
Bolt Set
  • francis from Columbia, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
15 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
seal for lint filter came off
Pulled out the old and slid in the new filter
Parts Used:
Dryer Lint Filter
  • John from Midland, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
17 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
parts took more than two months to get here.
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Parts Used:
Dryer Tri Ring Dryer Drum Support Shaft Dryer Drum Support Roller Shaft Right Hand Threads Dryer Drum Support Roller
  • rodney from Mad River, CA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
14 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer gasket detached from screen
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Parts Used:
Dryer Lint Filter
  • Richard from Duarte, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the dryer was making squealing noises when it first started.
We watched the video at whirlpool.com! Made it so simple anyone could have done it!
Parts Used:
Dryer Repair Kit
  • Christine from BIRCH RUN, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
12 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rear dryer drum seal came out
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Parts Used:
Drum Seal w/Adhesive
  • William from Pontiac, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set
17 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MLE22PRAYW0
31 - 45 of 747