MMV4184AAB - Instructions

The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.

unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .

It wasn't so much a repair as a replacement. If I had only found PartSelect earlier! I made the huge mistake of ordering a replacement from Sears - since that's where I bought the microwave. The pictures on their website are blurry - it's VERY difficult to tell which plate is the right one. Of course the one I got wouldn't work, so I had to send it back. Except that it didn't come from Sears, it came from a totally different vendor and I have no idea if they will honor the return with a refund, because of 'restocking fees'. Oh well. I found PartSelect, and the rest is all good. Your website is great. I found the right plate immediately - the pictures are clear and you can SEE what you're getting. The turn-around time between ordering online and receipt of the plate was phenomenal! SO QUICK! Thank you, PartSelect for making it so easy for me! Y'all are the BEST!!!! Jerel

Replaced light bulb.

remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

I put in the filter. The "over the stove microwave" made installation so easy even a woman could do it!

Lifted up the glass plate and stuck the assembly under it ;)

The turn table motor stopped turning ,but we never turned the off button off on the microwave and kept using it ,so it shorted to the outlet neutral (white) wire at the circuit breaker fuse panel , the wire burnt off. I cut the wire re-installed it in a good buss connector.That restored power back to the outlet.** So now to replace bad Turn-Motor: Using phillip screw driver remove (bottom)filter/light panel- 10 screws, unplug lights and motor connectors, lower panel out of the way ,remove 2 screws from motor and replace motor. Install in reverse order. (Fast Fix)**Note:If you had other problems like I did consult with a professional electrician.

You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!