MVWB750WR0 Maytag Washer - Instructions

Was pretty strait forward. Took the back panel off, removed the 3 mount screws and 2 clamps on the pump, and swapped it all out. Only thing, Paid for 2 day air shipping, took a week for the part to come in. But it was still faster and cheaper then my local parts dealer.

two small compression clamps hold the hoses in place. these are very simple to remove, however to reinstall the new hoses you should unscrew the pumps with a nut driver, secure the hoses with the clamps, and then screw the pump back to the bottom of the drum. oh yeah make sure to put the back plate back on the machine

I wasn't able to turn the washer on it's side or front, and instead had to prop it slightly up on cinder blocks due to the configuration of my laundry room. The actual repair was fairly simple, had the clamps supplied been easy to manuever, but they were not. The clamp that goes around the hose from the pump into the inlet valve wouldn't go down around the valve where it was supposed to. I had it too far up, so when I ran the washer, the whole hose popped out and flooded my laundry room. My husband suggested a better clamp, the type that actually opens and you can tighten with a screw system. $2.16 at Lowes. 2nd attempt at repair was successful, and so far no leaks. So...save yourself some time and when you get the replacement pump, take those clamps over to Lowes or Home Depot and buy a clamp that you can open fully, slip over the valve, and tighten as much as you need. If I had that type of clamp to begin with, this project would have taken an hour, tops. And by the way, I'm a 36 year old woman with NO experience fixing appliances, but plenty of experience paying other people too much money to fix things that never should have broken in the first place!

The most difficult problem was to identify where the leak was and I tried to repair the old pump but that was a waste of my time. I was most impressed with this company in how fast the order was taken and the perfect part was shipped to me. I received the part in approx. 30 hours after I placed the order. The part was delivered by FedExpress to my front door. A very reasonable price for the part. Anyway, most anyone could have done the repair that I did without difficulty.

Dismantled washer lid to install new locking mechanism.

First replaced four basket spring supports. Next tried Basket hub assembly ( which showed wear, but not total solution). Next replaced the rotation sensor that's on the stator. That finalized the issue.

Watched a couple of videos online to get a good grasp on repair. Opted out of purchasing the bearing press tool $130. Struggled a little, but made the repair. At the very least the wash tub needed a good cleaning

My problem stemmed from a previous leaky bleach dispenser hose (repaired over a year ago). It had leaked just above suspension rod assembly (only 1 of 4 was effected).Rod had rusted to point where it snapped just below the top mount. This actually made the replacement very easy as the rod simply slid out of the bottom tub channel and onto floor when washer tilted 45 degrees. Before tilting washer, unplug washer and disconnect supply lines and drain hos Use pry bar to separate cabinet top from cabinet lower section. Tilt top section to grant accesses to top suspension rod retainer mounts. Remove black rubber retainer washer from new suspension rod. As assistant holds tilted washer, a new suspension rod can be pushed thru bottom tub channel. Place black rubber washer back onto suspension rod. This will prevent the new rod from sliding full back out tub channel when released. The purchased suspension item has four rods and four top retainers. I could have reused the old retainer, but would have been more difficult to release the remaining rusted rod bit. So pulling up on rod and twisting suspension rod such that rod hook end pass thru top cabinet retainer cup and slides into position on new rod hook end retainer. Release retainer and rod, and move tub side to side allowing retain to assume natural position. (reference the other 3 retainers). Realign mating surfaces of cabinet top and cabinet lower if needed. Close cabinet top onto cabinet lower. Connect supply lines and drain hose, Plug unit in. Repair complete.

Pretty easy! Just follow this link on how to fix the problem:

https://www.youtube.com/watch?v=_-Hg8rLGiKQ

The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be.

Removed the center cover of the agitator with a flathead. Removed the nut of the agitator main cover. Had trouble taking the cover off because of the crud holding it down I wiggled it up gently alternating n,s and e,w until I eventually saw it separating from the bottom of the basket. Once it came off you could see how nasty the old hub assembly looked. Took the screws off the old hub assembly and removed it. Matched it up with the correct new hub assembly cause the kit comes with 2. Cleaned the shaft and that general area. Installed the new hub assembly, replaced the covers. Ran the drain and spin cycle and it worked with no problem. There are videos on YouTube that show you too. DO NOT try to pry the agitator cover if it won’t rise up easily. Be patient and it will come out.

Removed agitator and basket hub parts and cleaned all parts of agitator then replace basket hub with new basket hub kit according to video ran washer but did not solve problem

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Turn off and unscrew hot -cold hoses and drain line. Unplug power and pull unit away from wall. Tip onto front of machine and lean it onto something that will give you enough room to work as the pump is on bottom left back of unit. Unscrew all back plate screw's and remove back panel and keep screw's handy. Three main screw's hold pump in place but loosen hose clamp's first and its out. Reverse what you just did and you should be good to go! Good Luck!!

removed back of washer. turned washer on its side .removed the 3 screws holding pump and the 2 hoses and the electric connection pump came right out. did the reverse to install the new one.stood up the washer and ran it to check for leaks.no leaks installed back of washerand done

Have the Maytag washing machine little over2 years and the water pump cracked - very disappointed.
Anyway, removed the back panel, unhooked the hoses, used 5/16 wrench to loosen up the screws, unplugged the power connector than replaced it with a new water pump.

It was an easy repair that I taught my 18 yrs old.