MVWC565FW1 Whirlpool Washer - Instructions

Replaced the drive belt and shift actuator but that did not fix the problem! So I ordered a transmission and this still did not fix it! I give up! Time to get a new washer!

I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!

Watch video on the site and the insulation will be easy and take about 30 min.

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

Getting to the actual hub is a bit difficult as it involves removing the accetuator and takes some time and patience, but when I tried to replace with a new hub, I found that the screws were stripped, so PartSelect walked me through the ordering process and helped me choose the exact size screws that I needed. Parts came quickly...I already had the hub waiting to be secured and the screws tightened easily. (We had tried using a similar size, but you REALLY need the whirlpool screws that go in there) No more spinning problems, and the machine is not jumping around anymore. Works just like before. This particular machine has to have this part replaced at least twice a year (luckily it's cheap),but saves us from having to buy a whole new machine. My son also told me that since I replace the part so often, best to replace the screws every other time as well.

Went with the instructions

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

There are a lot of complaints, with these new energy efficient washers, no matter the brand, on the amount of water that is being used, and not properly washing your cloths, while in the wash cycle.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.

Pop center cover off wash plate. Remove bolt. Lift off washplate. Slide retainer off with screwdriver and hammer. Slide new retainer on. Replace washplate.

My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!

Removed old one (2 screws) slid in place and screwed in.

Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 cheaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.

followed instructions that were e-mailed and they were easy to follow.

remove basket and replace drive hub kit