RTW4516FW2 Whirlpool Washer - Instructions

first I removed the fabric softner and water seal from center of agitator, then I removed the bolt holding it on. All I had to do then is install new agitator with old bolt place water seal and fabric softner container back on and start washing clothes again. Very simple.

The repair was very easy. The only hard part was due to the age of the machine the cap covering the agitator assembly was stuck on the top.I had to use a very large pipe wrench to loosen it. Other than that the whole repair went very smooth. You will need an extension with the socket wrench in order to reach the screw holding down the agitator.I was very impressed with the service from Parts Select. I received my part very fast and it included everything I needed to complete the job.

After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!

First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting washer back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.

First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.

The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you

Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.

Followed youtube video. The repair was easy and fast.

First I removed the fabric softner dispenser. Then I removed cap took screw out removed agitator asseembly put new one in then I put screws back in.

THE NEW LATCH COMES WITH A NEW BEZEL ATTACHED, WHICH MOUNTS TO THE TOP OF THE WASHER, JUST UNDERNEATH THE LID. BECAUSE THE ORIGINAL BEZEL WAS IN PERFECT CONDITION AND DIFFICULT TO REMOVE, I DECIDED TO REMOVE THE BEZEL ON THE NEW LATCH, AND USE THE ORIGINAL ONE. THIS WOULD HAVE TO BE DONE REGARDLESS IN ORDER TO INSTALL THE NEW LATCH. REMOVING THE BEZEL WAS DIFFICULT DUE TO ALL THE LOCKING TABS THAT KEEP IT IN PLACE. I HAD TO RESTRAIN THE SLIDING SWITCH PARTS WHILE I REMOVED TO BEZEL TO AVOID THE ASSEMBLY FROM COMING APART. ONCE I SNAPPED THE NEW LATCH TO THE EXISTING BEZEL, THE ASSEMBLY WORKED FINE. TAKE TIME TO STUDY HOW THE LATCH ASSEMBLY IS ATTACHED TO THE BEZEL SO THAT YOU DON'T BREAK SOMETHING. USE A VERY SMALL SCREWDRIVER TO PRY BACK THE PLASTIC TABS IN ORDER TO RELEASE THE BEZEL FROM THE LATCH ASSEMBLY.

I was able to look up the issue on Youtube and watched a few videos and was able to complete the repair with help of my daughter. It was little hard to do but you do need gloves with a good grip when taking the rods out of the washer, but putting the new ones in was very easy.

Once I replaced the suspension rods, there was a little shaking but not like before. Very quiet now, no crazy loud banging

Unplugged from power, unhooked water lines.Then removed back cover and control panel and top set to the side. Rear rods very easy to do by yourself after those where done have help and tip it backwards and change out the front 2 then reassembled and hooked back up and tested. Everything worked like brand new !!!

Youtube has videos. It's very simple just replace one at a time.

The installation was very easy and took me 45 minutes to complete by myself. I put the washer on two cinder blocks and then removed the lid. I started with the suspension rods that were closest to me and they were really easy to exchange. When I got to the rods in the back they were a little more difficult because there was more tension with the new rods installed. I used the old rods to hook and pull the new rods into place and it was overall very easy.

Unplug washer
Take back panel off
Un plug lid switch
Take screwdriver snap out switch
Snap in New switch
Plug it in
Replace back panel plug in washer
Wash