Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Leakage developed from holes in drain hose
Two people make the job easier: the smaller on his back doing the work, while the other positions lights and provides tools. Remove bottom panel. Loosen and slide the two small spring clips back from fittings. Locate (out of sight in the back) and loosen the screw-type tensioner on large, upper clamp. Remove old hose and position clamps on new hose. Seat all hose fittings securely and reposition spring clamps. A bit of soapy water for lubrication can help. Tighten down screw tensioner on large clamp. Test by pouring bucket of water into washer.
I followed the steps in the You Tube video on this topic. Search for "washing machine repair - replacing the drive pulley" in your favorite search engine. The video is very well done and it is a simple fix. Before I put on the new drive pulley and nut, I vacuumed up and then wiped down the black dust around the drive pulley shaft (as well as on the inside floor of the washer) to make sure the drive pulley slid onto the shaft using the hand banging method described in the video (dust was likely from the belt due to the excessive movement of the drive pulley). While it may be possible to tighten the nut without a torque wrench, I personally had trouble judging the appropriate 44 ft lbs of torque without it (i.e. my snug required more than a quarter turn per the optional instructions). The torque wrench provided me with the assurance that I installed the drive pulley correctly.Two of my shocks were leaking slightly so I assumed that was the primary issue and replaced all 4 at quite a hefty cost. It helped with the noise but not significantly. If you do have a loud noise during the spin cycle, do yourself a favor and check the play in the drive pulley and look for the black dust before you diagnose the problem to be something else. The online diagnostic tool showed the drive pulley as being the highest probability of being the issue so, sadly, I have no excuses...
Most front load washers have drum rear support (spiders) that disintergrate prematurally
If the washer basket "crashes" or thumps while rotating, the spider must be replaced. I have found that, although difficult, the spider mounting bolts can be removed without sheering if starting to unscrew until it jams then hit the bolt once with a hammer and try again to unscrew. It will give just a little and keep repeating the process until the bolt is completely out. I have tried heating with a torch, chisel tapping and re-tapping the threads after drilling out the bolt but the method I described is the most successful. After removal I bring the spider to a local powder coating person for a permanent coating of preservation. This site provides the least expensive new spiders or spider basket assemblies available. E-Bay provides used items also.
Broken tub assembly. The part that broke is also known as a "spider". Drum was wobbling around inside machine and making bad noise.
Disassembled the washer from the top down more or less. Started with top cover, then control panel then door assembly. After that removed all connections to drum. Removed belt, pulley, and then counterweights. Wires are all on harness with plugs, I took pics as I went for reference as to where they belong. The motor was left plugged in and slides out of the mount at the bottom of the tub after removing one bolt. To remove the door latch assembly, remove the front tub seal first then you can easily access it after you unscrew it. The shocks are a quarter turn release type mechanism. I broke two going back together after trying to lock them into place. Not sure why, maybe age of part had something to do with it, and they are hard to turn as well.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
7 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not turn on without numerous pushes of the power button
Disassembled washer to get access to power board, removed both power and start/pause switches and replaced them with new ones. Reassembled washer. Works well. The most difficult part of appliance maintenance is learning how to disassemble the machine. Videos of the process are very helpful.
Unplug machine. Remove band from front bellows by prying the spring at 6:00 o:clock loose. Pull back bellows on right side. Remove 3 torx screws and gently pull door each lock assembly out. Unplug 3 wire harness connectors and plug into new latch lock in same order. Screw new latch lock in place and replace bellows and band. Done
We ultimately rebuilt this washer because I love it so and it was one-half cheaper to rebuild than to buy new! We watched videos and researched the repair and then dove in. Yes, we had to tear the machine down but really it was not that bad of an ordeal. It ended up being much easier than we initially thought but once all the parts arrived we fixed it!
I ordered a new control board but couldn’t find any YOUTUBE instructions. Finally I found one where you got the control board and the panel so I had to take the panel off and attach it to the new board. Since I paid $372 for the board I was very scared, but the whole thing came back together and worked perfectly. All and all a scary but inexpensive repair (I’m sure a tech would get $900-1000).
The repair video was almost perfect. I would not have even attempted the repair without the video as I am not a handyman at all. The diagnostic feature based on the symptoms was invaluable. I originally took the front of the washer off because I thought the rubber seal around the door was leaking.It was like 67% of the problem. But after checking the front seal carefully, I determined it wasn't. The next most likely issue as only rated 19% but when the water inlet pipe, I was actually tickled to see a crack in the plastic pipe. I ordered on line on Monday and with the cheapest shipping, I received my part in the mail on Thursday. I would highly recommend using Part Select for diagnostic, parts and repair. I will definitely use again. If I could make one recommendation to Part Select, it would be to do a close up during the video when the technician is working with a part, i.e., the wiring that goes around the rubber seal.
Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.