WRX735SDBM00 Whirlpool Refrigerator - Instructions

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Truth is, this took a couple hours of cursing, but that was due to poor information and no prior experience. I imagine the next one would take 20 minutes. The issues are these: videos tell you to use a putty knife to pry the old switch out. That is harder than it seems because each switch has a plastic spring that pops open to hold the switch on, and you can't access the spring when the switch is installed. So it is important to use the knife on the side of the switch (left or right of spring -- look at the new switch), and back and forth until the switch is worked out. Then it can get worse. The new switch has to plug in electrically before it can be installed mechanically. In my case, with the switch on the fridge wall rather than the top, the outlet for the plug was encased in foam insullation. That gives the appearance that the plug was fixed, immovable, which makes it impossible to plug it in electrically before the switch is in place, and of course once it is in place you can't then plug it in. The problem here was poor instructions. Just scrape out a lot of the foam around the plug and you find that the plug is really not fixed, but attached to reasonably long wires that allow you to plug it in with the switch a couple inches from the wall, and then insert the switch. None of the online instructions tell you this about the wires.

Simple. Just put it on the racks provided in the fridge. The part fit perfectly and took literally 5 seconds to put it on.

Pulled the whole assembly out and unscrewed the Ice maker and old wire harness loose. pulled one wire at a time loose and put the new one in place one wire at a time so not to get them wrong. Then the ground wire I cut and stripped and used a wire nut to connect the two green wires together. Otherwise you would have to take more things off to get to the 1/4 nut on the ground wire. Then put the three screws back in the ice maker bottom.Slid it back in place and plugged in the new wire harness. And put the plastic cover back in place to cover the wires. You can also look on U-Tube to see how it is done. They just do not show the new harness I was sent. I guess the ice maker I got fit other models.

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)

Let the ice in the freezer melt while installing P trap drain tube

you tube video was most helpful. after getting new part and disassembling old ice maker, you have to change out the wiring harness. Reinstall ice maker, don't worry about the timing of the unit as it will do this itself, may take 10 hours to produce ice, mine took about 2 hours to go through its' cycles and give me ice. It is running great

Saw U tube instrctions how to install and it was easy

First found U Tube video of my exact refrigerator, ice maker remove and replace. Many available, all are helpful. Watch several times. Once part arrived the repair went very smoothly. Only had some difficulty attaching the ground wire, had to loosen the auger motor to attach the tiny screw. Not difficult, just took a bit of time to get the angle on the screw correct.

Open and remove door by loosening two screws on both sides of the door. Lift up and away the door.place the door on flat surface, grab and lift up on seal pulling out of reach. Clean track, alone seal on food before pressing in place. Check to make sure seal is set in place. Install door job done.

The ice selector solenoid was a snap to replace.
You do have to pull the ice maker out. I looked on you tube to find out how to take off the wire cover and how to release the ice maker so it will slide out.
Firmly grab it and pull try to keep it level while pulling and it will slide out better.
After removed its 2 small screws and a release clamp to get the old part off and snap the new one in replace screws and wires.
The toughest part of this was figuring out that it was the solenoid in the first place.
Best of luck do it yourselfers like me.

I ordered the wrong part for my refrigerator. The refund processed easily. However, the email that I was promised with return instructions has not been sent. I have asked several times about how to return this part and total silence from partselect. I'm ready to throw this replacement bin in the trash.

Removed old shelf and installed new shelf. No tools required

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.