YTD74E2SN1WS General Electric Dryer - Instructions

Very simple and easy it took no more than 10 seconds if that long. Remove the worn out screen (pull up and out), replace it with the new screen( slide it into the area where the old screen was removed. (No tools needed)

Just put new lint filter in slot
I had torn the screen on the original one

Having 2 persons make the job easier.
1) Remove the screws that holds the hinge to the body of the unit.
2) Remove the screws around the door so you can get to the hinge.
3) Remove bad hinge and replace with new one.

remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.

Found the dryer's high limit thermostat had opened up.
Likely cause was excessive lint buildup in exhaust vent pipe to outside.
Used wire nuts to "temporarily" bypass thermostat and cleaned out the vent pipe
When new part arrived...

Removed control panel screws and panel was laid on top of dryer
Removed back panel screws.
Removed top panel screws. Lifted to allow right side swing out slightly.

I did not have sufficient tool to reach the thermostat therefore I reamed out a hole in the rear panel above the thermostat fastener screw to allow a long handle screwdriver into the area for replacement.

Removed temporary bypass and used wire nuts to utilize dryers' thermostat existing wiring.

I just popped in the new Filter and it fit perfectly. This will prolong the dryer use, looks like new.

Thank you Part Select.

One Happy customer

Lift the lint filter and slide the 2 hooked ends into the 2 holes provided . Front end is locked in as other end is suspended .

Took the front panel off. 2 screws on top of the front panel when you open the door, 2 right next to the door opening. Next gently pry up the top panel in the front of the dryer to remove 2 black screws in the front corners. Now the front panel can gently be pulled back and then lift up and the frpnt panel can be put to side. Now you have acces to remove and replace the drum bearing glides. They just clip in. Also a good time to inspect the belt and clean out the dryer.

removed old lint trap cleaned excess lint that fell inside from the broken lint trap made it easier for new lint trap to slide in.

After checking the obvious things such as household circuit breaker and verifying that the dryer power outlet did indeed have the proper voltage supply, I started troubleshooting the dryer itself. The "partselect.com" website has a lot of good troubleshooting information. I used it to narrow my search and began by checking the fuse located where the power cord connects to the dryer. From there I used the information that the website provided for finding and checking the overtempt switch for the dryer. It's located in a very hard position to get to, and it was indeed bad. I ordered a new one from the "partselect.com" website and started checking my dryer exhaust vent hose for a blockage, as that was the most practical cause for the overtempt switch to fail. Once I verified that the exhaust was clear from any obstruction, I set my sights on removing the bad overtempt switch.

I have over 30 years' experience troubleshooting and repairing both AC and DC electrical and electronic circuits and systems. I'm 6'4" and have very big hands and it was next to impossible for me to get my hands in a position to loosen and remove the 1 screw that was holding the switch in place. After an hour or so I was finally able to remove the switch. There was no way that I was going to be able to successfully install the new switch due to the lack of space. I ended up going back to the "partselect.com" website to see if anyone else had this same issue and found a way to overcome it. After few minutes of reading thru different installation comments from other people, I found one that had the key to quickly and accurately installing the switch. This person used a drill and drilled a hole in the back panel of the dryer to gain access to the screw that holds the switch in place. So, I drilled a small 1/8" hole in the back panel directly across from where the head of the screw was. I used several more drill bits and worked my way up to a 1/2" sized bit. Then, I used a 1/4" drive socket set with a 10" extension and 1/4" socket to install the screw retaining the switch. I reassembled the dryer and have had no other trouble since.

Follow YouTube "how to change dryer's belt" some video is very clear.

used you tube and with your info. actually took apart dryer replaced part & reassemble

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair

had a great video to follow, made it easy to install.