This genuine OEM oven probe is also known as an oven temperature sensor or range probe. This part is manufactured for a range, stove, or oven to detect the temperature within the oven cavity. The probe allows the oven to maintain the set temperature by sensing the temperature and sending the information to the ovens motherboard. You may need to replace this part if oven is not heating or is heating unevenly. Be sure to disconnect power to oven before replacing, as it is an electrical part. Tools needed are 1/4 inch nut driver and needle nose pliers.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Range Temperature Sensor
Troubleshooting
This part fixes the following symptoms:
Oven is too hot | Little to no heat when baking | Oven not heating evenly | Element will not heat
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Debra B - May 1, 2024
Verified Purchase
Easy Repair
The part came fast. Worked great. Oven back in to working great.
★★★★★
★★★★★
Stacey C - February 7, 2024
Verified Purchase
Quick delivery and easy installation
Our 10 yr old Frigidaire stove gave error code that oven was getting too hot. Determined that we needed a new broil element and heat sensor. We received the parts in 3 days, very easy to remove old and install the new parts.
★★★★★
★★★★★
Raymond H - December 2, 2023
Verified Purchase
Temp sensor
Part arrived fast and in great working condition, im very pleased with all service,
★★★★★
★★★★★
Donna L - December 1, 2022
Verified Purchase
Easy Repair
The part was in excellent condition and was very easy to repair. Working great!
★★★★★
★★★★★
Wayne P - August 5, 2022
Verified Purchase
Oven not heating
Didn’t take care of the problem oven temperature low or not at all
★★★★★
★★★★★
Brian S - July 27, 2022
Verified Purchase
Easy install
Easy install met my need of replacement part
★★★★★
★★★★★
Vernita C - July 16, 2022
Verified Purchase
Easy repair
The part was in great condition and came rather quickly. My oven is up and running.
★★★★★
★★★★★
Janet T - January 27, 2022
Verified Purchase
Very Happy
Works well. Thank you.
★★★★★
★★★★★
Eric B - October 18, 2021
Verified Purchase
Did the trick, easy repair and fast shipping
Temp sensor was the ticket to stove working properly, no more F10 codes.
★★★★★
★★★★★
Robert Rojas W - July 24, 2021
Verified Purchase
PartsSelect recommended, as advised, part repaired oven.
As advertised, fast delivery, correct part. great instructions. Appliance working as new.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 25 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Oven temp runaway tempreture, oven light out, sensor was changed for temp drifting low
The light and sensor were straight forward and easy. The EOC was as well but there was one glitch. You have to also purchase the black panel overlay, you cannot use the old one. While the adhesive will still adhere, the keypad is different and REQUIRES the new cover. This would have been good to know when I ordered parts as I did not
... Read moreknow until I got the three parts and had to reorder the overlay creating a weeks delay in it's repair.
first the temperature sensor then the igniter. started to do the igniter by using common sense then I used YouTube which made it a lot faster. the temperature sensor installs from the back of the stove, the igniter installs from thr front ie, the drawer and inside oven.
SHAUN from ALBUQUERQUE, NM
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven temperature was not consistent.
I pulled the oven away from the wall, unplugged the cord, removed the back panel then removed the screw from the old sensor.
Kimberly from OWASSO, OK
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven temp was not heating up to desired temp and using an oven thermometer to confirm
moved the range out to access back removed 5 screws from back panel removed 1 screw from thermostat installed new one replaced screws, done in 20 minutes problem solved
philip from CLIFTON, NJ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F10 Code/ Oven Temperature not working
Removed back panels and removed temperature sensor, which was extremely easy, and replaced with new sensor. Only one hex screw holding it in place. Replacing control board was surprisingly easy as well. Just take a photo of where all the wires connect (only two to unplug) and use a putty knife to remove the touch pad (doesn’t come w
... Read moreith new control board). The touch pad was still sticky so it adhered to the new control board with no issues. Then plugged oven back in. Voilà! Oven worked again!
Oven would not heat or sometimes hold heat to set temp
I was able to find the most common reason for my oven's symptom by searching online. I searched for the part I needed but was not confident that I would get the correct part until I looked on partselect.com. After verifying the part number with my owners manual and looking at the video on their website, I decided to order. PartSelect ship
... Read moreped the part as expected, and I was able to install it in less than 30 minutes. The only tool needed for installation was a nut driver. My oven is now working like new.
Many thanks to PartSelect for their comprehensive website and fine service.
Read less
TRACY from NEW PHILA, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
run away temp
I changed the temperature sensor and tried again. The stove again went on temp runaway and it was suggested to replace control board which is out of stock. I will have to toss out this stove and buy new as you and no else has this part.
James from ELKHORN, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F10 code going off
Went well, and working thank you ??
edward from BRISTOL, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wasn’t heating
Used instruction video & replaced part.
Felicia from FORT MILL, SC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I had a F31 code which means oven isn't working
Called fridgidaire and they told me the a F31 code means my temperature sensor is not working. So I ordered one online. I installed it and I still have F31 code and still won't work. So what now? Do I trust them to tell me another part?
Terry from CHELSEA, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
37 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Delano
November 24, 2019
Oven temp won’t go over 250 degrees. It also takes about 30mns to reach that temp.
For model number LGEF3045KFK
Hello DeLano, thank you for your question. The most common part that causes that issue is the oven sensor prob PartSelect Number: PS1528542. You can test it with a multi meter. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!
49 people found this helpful.
Was this helpful?
Thank you for voting!
Edward
November 28, 2019
Used the self cleaner on the oven, and now it won't come on to bake. Broiler seems to be working. I have seen posts about a thermal fuse. Any help would be great. Thank you. I would like to repair it myself if possible. Not a good day to happen.....thanksgiving day!
For model number FFEF3017LSG
Hello Edward, Thank you for the question. I suggest testing the Oven Probe Sensor, PartSelect Number: PS1528542. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!
15 people found this helpful.
Was this helpful?
Thank you for voting!
Rona
December 24, 2019
My oven does not heat evenly. I had the oven probe (sku# 31690003) replaced but it did not fix the problem.
For model number wfe324lw0
Hi Rona, thank you for your question. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. I hope that helps. Good luck with your repair.
9 people found this helpful.
Was this helpful?
Thank you for voting!
Desiree
October 26, 2021
Hi. Stovetop burners, clock and all displays working fine, but the oven is not coming to full temp. Last night it took over two hours to get to 227 degrees F. Have not seen either element glow orange, but by touch they are definitely heating up some, just not a lot. Have not been able to view bottom element, as one screw is rusted or stripped, and I haven’t been able to get it out yet. Are the heating elements a binary type thing? Are they ever “partially working,” or is it a case of: if they are heating at all, the issue is probably something else? Is it possible that this issue could be caused by a bad temperature sensor? If so, can that be tested without removing? Just trying to figure out what to check next, or what the issue likely is. Thanks so much for any help! Desirée
For model number LGEF3045KFB
Hello Desiree, Thank you for the question. This is normally an indication the Sensor is defective. In order to test it, the sensor will need to be removed. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. We hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
IKE
November 2, 2021
What is the temperature sensor part number and the location of it in the oven?
For model number FGF368GQF
Hello Ike, Thank you for your inquiry. We have researched the model number you have provided and show the part number as PS1528542. It is located on the right hand side of your oven. We have included a link to our repair video on installing the part. We hope this helps.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Frank
October 29, 2019
The oven does not start up, replaced element. Still does not start up. Would it be the temp probe ?
For model number 79094142312
Hello Frank, Thank you for the question. It is possible the probe is defective. You can test it with a multi meter. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. If both elements are not coming on, it is more then likley a defective Electronic Control Board PartSelect Number PS8689401. Hope this helps!
How do i know if it is an igniter or a sensor? My oven doesn't get hot igniter is orange.
For model number ffgf3023lwd
Hello Pat, thank you for your inquiry! We recommend replacing the Oven Bake Igniter if your oven isn't getting hot. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. I hope this information helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Read
November 7, 2019
My oven will not start after cleaning. The igniter comes on and after about 10 seconds it trips the GFCI. I suspect a thermal fuse, but I cannot find one in the parts list.
For model number LGGF3043KFV
Hi Read,
Thank you for your question. There is no fuse for this model. According to your owner's manual, where your oven is a self cleaning oven, it cleans itself with high temperatures, which eliminates soils in the oven or reduces them to ash that you may wipe away with a damp cloth. The heat from the oven during the self cleaning may have damaged a wire in the oven that may be causing the breaker to trip. You will need to check with a technician to verify what is causing this issue. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Martin
November 10, 2019
Surface burners and oven is not working but clock setting is working.
For model number FEF368GBA
Hello Martin, thank you for your question. The oven control board is what control the oven. If the oven isn't working at all (bake or broil) the electronic board should be replaced. The surface burners are controlled by the infinite switches. We would recommend testing the switches to determine if they are faulty. I hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Amanda
November 23, 2019
Can a temp. Sensor be going bad and still read good on a meter. Oven seems to lose heat and quit working after preheat. Sometimes u can turn it off and on and it will start back working group right everything going else works fine no codes either
For model number Ffef3015pwb
Hi Amanda, the temperature sensor is part PS1528542. Thank you for your question and good luck with your repair!
