Part Location Diagram of 530095646 Husqvarna Engine Fuel Filter
See part C56 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Engine Fuel Filter 530095646

★★★★★
★★★★★
2 Reviews

Rated by 5 customers 

Really Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 4.99
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

Does this part fit my model?

Need help finding your model number?
PartSelect Number PS9285148
Manufacturer Part Number 530095646
Manufactured by Husqvarna for Husqvarna, Poulan, Weed Eater, Paramount
Product Description

Engine Fuel Filter Specifications

This fuel filter is for lawn and garden equipment engines. Fuel filter cleans the fuel before it reaches the carburetor. Work in a well-ventilated area when installing this part. Drain the fuel tank and disconnect the spark plug wire before beginning the repair.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start | Engine stops after a few seconds or minutes
This part works with the following products:
Trimmer, Chainsaw, Leaf Blower / Vacuum, Edger.
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 3.2 / 5.0, 5 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
Both the Fuel line and the Engine fuel line, where dry rotted.
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines.
2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank.
3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fall into the path of the new fuel lines installation.
4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor.
5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line.
6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary.
7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
Other Parts Used:
Fuel Line Tank Purge Line Engine Fuel Filter
  • Victor from SCOTTSVILLE, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
38 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fuel and Purge lines had disintegrated
Disassembled it and cleaned fuel tank. Cut and ran new fuel lines, installed filter and reassembled. Parts fit perfectly and got running after not running for over 20 years.
Other Parts Used:
Fuel Line Tank Purge Line Engine Fuel Filter
  • Casper from ERATH, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
24 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the fuel lines
Replaced all fuel lines. Followed instructions found on Partselect.com, which said to insert cut fuel line in tank and use forceps to reach back in the tank and pull the fuel line through. The problem was that I did not have forceps, or needle nosed pliers that could reach the end of the hose.

Instead of running the line into the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through.
Other Parts Used:
Fuel Cap Assembly Fuel Line Tank Purge Line Filter-Air Bulb-Purge "snap-in" Fuel Line Fitting Engine Fuel Filter
  • Robert from MANVILLE, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
15 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Deterioration of fuel line system
Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark
Other Parts Used:
Primer Bulb Kit Fuel Line Tank Purge Line Foam-Air Filter Fuel Line Fitting Engine Fuel Filter
  • Mark from LYNDONVILLE, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
95 of 103 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Weak spark. Multiple fuel leaks/ no start.
Pull #25 torx 4mm screws until you find the ignition module. Replace it, use lock tight, gap with a paper credit card. Reassemble. Replace cap and fuel lines. Pump and pull till it blows the carb cleaner and Blaster out and starts.
Other Parts Used:
Ignition Module Fuel Line Tank Purge Line Fuel Cap (w/ retainer) Engine Fuel Filter
  • Anthony from ST GEORGE, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
42 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bill
August 15, 2023
What is the order of the two gaskets located on the under side of the Carburater.They fell off doing fuel bulb replacement.
For model number TE 475 Y
PartSelect logo
Hi Bill, thank you for getting in touch. The gaskets you are looking for are not sold separately, they come in a gasket kit, part number PS9472663. If you need help placing an order, customer service is open 7 days a week!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Philip
June 10, 2024
Ware is the fuel filter located on this mod. chain saw, I can't seem to find the location in the manual Thanks Philip
For model number PP4218AVHD
PartSelect logo
Hi Philip, thank you for the question. The fuel filter in your unit is located in the fuel tank. We hope this information is useful!

Was this helpful?
Thank you for voting!
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS9285148
Manufacturer Part Number: 530095646
Brand
Model Number
Description
Poulan
033
Trimmer - Poulan String Trimmer Model 033 Parts
Husqvarna
112
Trimmer - Handheld Trimmer
Husqvarna
122HBV
Leaf Blower / Vacuum - Husqvarna Leaf Blower Model 122HBV Parts
Husqvarna
124C
Trimmer - Husqvarna String Trimmer Model 124C/2006-05 (124C/200605, 124C/2006 05) Parts
Husqvarna
124L
Trimmer - Husqvarna String Trimmer Model 124L/2006-05 (124L/200605, 124L/2006 05) Parts
Husqvarna
124R
Brush Cutter - Brushcutter
Husqvarna
125B
Leaf Blower / Vacuum - 28cc 2-Stroke 170-MPH Gas-Powered Handheld Gas Blower
Husqvarna
125BV
Leaf Blower / Vacuum - Husqvarna Leaf Blower Model 125BV Parts
Husqvarna
125BVX
Leaf Blower / Vacuum - Handheld Leaf Blower
Husqvarna
125BX
Leaf Blower / Vacuum - Handheld Leaf Blower
Husqvarna
125C
Trimmer - Trimmer
Husqvarna
125C-CANADA
Trimmer - Gas Line Trimmer
Husqvarna
125E
Edger - Edger
Husqvarna
125E-CANADA
Trimmer - Gas Line Trimmer
Husqvarna
125L
Trimmer - Trimmer
Husqvarna
125LD
Trimmer - 125 Ld, 20061000001-20064900000
Husqvarna
125LDX
Trimmer - Husqvarna String Trimmer Model 125LDX Parts
Husqvarna
125LDXTEST
Trimmer - 125ldx Test (2010-06)
Husqvarna
125LSST
Trimmer - Gas Line Trimmer
Husqvarna
125R
Brush Cutter - Brushcutter
Husqvarna
125R-CANADA
Trimmer - Gas Line Trimmer
Husqvarna
125RJ
Brush Cutter - Brushcutter
Husqvarna
128C
Trimmer - Trimmer/Edger
Husqvarna
128CD
Trimmer - 28cc Gas Line Lawn Trimmer
Husqvarna
128CD-LOWES
Trimmer - Gas Line Trimmer
Husqvarna
128DJX
Trimmer - Husqvarna String Trimmer Model 128DJX Parts
Husqvarna
128L
Trimmer - Husqvarna String Trimmer Model 128L/2008-09 (128L/200809, 128L/2008 09) Parts
Husqvarna
128LD
Trimmer - Trimmer/Edger
Husqvarna
128LD-LOWES
Trimmer - Gas Line Trimmer
Husqvarna
128LDX
Trimmer - Husqvarna String Trimmer Model 128LDX/2008-12 (128LDX/200812, 128LDX/2008 12) Parts
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service